Disposal And Recycling; Storage And Transport - EINHELL AGILLO 36/255 BL Originalbetriebsanleitung

•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
•
Use a brush to remove deposits from the
safety guard
7.2 Replacing the line spool
Danger! Remove the battery packs!
1. Fig. 22 Press the line spool housing together
at the points marked M and remove the spool
cover.
2. Take out the empty line spool and the pressu-
re spring.
3. Fig. 23 Thread the end of the line on the new
line spool through the eyelet (P) in the spool
cover and allow approx. 13 cm of line to pro-
ject. Insert the pressure spring (N) in the line
spool.
4. Press the spool cover back into the line spool
housing.
7.3 Replacing the cutting line
Danger! Remove the battery packs!
1. Fig. 22 Press the line spool housing together
at the points marked M and remove the spool
cover.
2. Take out the empty line spool and the pressu-
re spring.
3. Remove any remaining cutting line if there is
any.
4. Fig. 24 Insert the new cutting line through the
line mount inside the spool.
5. Wind the line with tension in a counter-clock-
wise direction.
6. Fig. 25 Hook the line, approx. 15 cm before
the end of the line, into one of the line holders
on the edge of the spool.
7. Fig. 23 Thread the end of the line on the new
line spool through the eyelet (P) in the spool
cover. Insert the pressure spring (N) in the
line spool.
8. Pull the line sharply to release it from the line
holder.
9. Press the spool cover back into the line spool
housing.
When you start the equipment again the line will
be cut to the perfect length automatically.
Caution! Bits of the nylon line could cause
injury when flung out!
Anl_Agillo_36_255_BL_SPK13.indb 28 Anl_Agillo_36_255_BL_SPK13.indb 28
GB
7.4 Sharpening the guard hood blade
The guard hood blade (Fig. 2/Item 14) can be-
come blunt over time. When you notice this, undo
the screw holding the guard hood blade on the
guard hood. Clamp the blade in a vise. Sharpen
the blade with a flat file and make sure that the
angle of the cutting edge is not altered in the pro-
cess. File in one direction only.
7.5 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.6 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.Einhell-Service.com
Spare line spool Art. No.: 34.050.96
Spare cutting blade Art. No.: 34.050.82

8. Disposal and recycling

The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offices.

9. Storage and transport

Remove the batteries. Store the equipment and
its accessories in a dark and dry place at above
freezing temperature. The ideal storage tempe-
rature is between 5 and 30 °C. Store the electric
equipment in its original packaging.
The equipment has an integrated wall holder (Fig.
26/Item L) to enable it to be hung on the wall.
- 28 -
16.08.2021 12:06:09 16.08.2021 12:06:09