Before Using The Equipment - EINHELL CE-CC 18 Li Originalbetriebsanleitung

5. Before using the equipment

This product is supplied without batteries and
without a charger and is allowed to be used only
with the lithium-ion batteries of the Power-X-
Change series!
•
Check the equipment for damage which may
have occurred in transit. Report any damage
immediately to the transport company which
was used to deliver the compressor.
•
Make sure that the intake air is dry and dust-
free.
•
Do not install the compressor in a damp or
wet room.
•
The compressor may only be used in suitable
rooms (with good ventilation and an ambient
temperature from +5 °C to 40 °C). There must
be no dust, acids, vapors, explosive gases or
inflammable gases in the room.
•
The compressor is designed to be used in dry
rooms. It is prohibited to use the compressor
in areas where work is conducted with spray-
ed water.
•
Do not clean your clothes with compressed
air.
•
Keep all the air vents free of foreign bodies.
•
Do not place the equipment on a heated
surface.
Warning! When using the equipment to infl ate
objects, check the information and safety
instructions provided by the manufacturer of
these objects.
5.1 Charging the lithium-ion battery pack
(Fig. 3, 4)
1. Pull the battery pack out of the handle,
pressing the pushlock button (C)
downwards while you do so.
2. Check that your mains voltage is the
same as that marked on the rating plate.
Insert the power plug of the charger into
the socket outlet. The green LED will then
begin to fl ash.
3. Push the battery pack onto the battery
charger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
Anl_CE_CC_18_Li-Solo_SPK13.indb 18 Anl_CE_CC_18_Li-Solo_SPK13.indb 18
GB
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit.
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.2 Battery capacity indicator (Fig. 5)
Press the button for the battery capacity indicator
(A). The battery capacity indicator (B) will indicate
the charge status of the battery by means of 3
LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
5.3 Fitting the battery (Fig. 3)
Push the battery into the battery mount provided.
When the battery is positioned as in Fig. 3, make
sure that the pushlock button (C) latches in place!
- 18 -
19.05.2021 12:28:19 19.05.2021 12:28:19