Optional Accessories; Maintenance - Makita DWT310 Betriebsanleitung

7. Pull the eject lever to eject the bolt tip from the
tool. Catch the sheared bolt tips to prevent them from
f alling.
Fig.16: 1. Bolt tip
NOTICE:
Washer and nut have head and tail.
Head has identification mark for nut and chamfer
for w asher. When placing them, be careful not to
place in reverse.
Fig.17: 1. Identification mark 2. Nut 3. Bolt
4. C h am f ere d 5. W as h er
NOTICE:
Replace nut, bolt and w asher all
together at one time w hen these rotate together,
nut rotates excessively or a bolt protrude from
nut surface too much or less.
NOTICE:
Do not reuse used nut, bolt and w asher.
The range for the remaining length of bolts after cutting
off the bolt tips are determined by bolt size. Refer to the
table below and choose shear bolts according to the
thickness of workpiece to be fastened.
Bolt size Maximum remain-
ing length
M1 6 20 mm
M20 1 5 mm
M22 1 4 mm
Fig.18: 1. R emaining lengt h
NOTICE:
Use bolts w ith the remaining length
w ithin the range sho w n in the table above as bolts
w ith different size have different maximum and
minimum remaining length.
NOTICE:
Be careful not to use bolts beyond
the specified range which may cause the tool
malfunction.

MAINTENANCE

CAUTION:
Al w ays be sure that the tool is
s w itched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Battery guard
guard. Do not use the tool w ith the battery guard
removed or damaged. Direct impact to the battery
cartridge may cause battery malfunction and result
in injury and/or fire. If the battery guard is deformed
or damaged, contact your authorized service center
f or repairs.
guard for hanging the tool.
the battery guard.
OPTIONAL
ACCESSORIES
Minimum remain-
ing length
4 .5 mm
are recommended for use w ith your Makita tool
5 .5 mm
specified in this manual. The use of any other
7 mm
a c c essories or atta c h ments mig h t present a risk o f
injury to persons. Only use accessory or attachment
f or its state d purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
C enter.
NOTE: Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.
9 ENGLISH
WARNING:
Do not remove the battery
CAUTION:
Do not attach a strap to the battery
CAUTION:
Do not attach the shoulder belt to
Fig.19: 1. Battery guard 2. Battery guard holder
CAUTION:
These accessories or attachments
Bolt size Sleeve
M1 6 O uter sleev e
I nner sleev e
M20 O uter sleev e
I nner sleev e
M22 O uter sleev e
I nner sleev e
M22 O uter sleev e
I nner sleev e
5/8 O uter sleev e
I nner sleev e
/ O uter sleev e
I nner sleev e
/ O uter sleev e
I nner sleev e
Makita genuine battery and charger
Length
35 mm
36 mm
37 mm
38 mm
39 mm
39 mm
8 5 mm
8 5 mm
35 mm
36 mm
37 mm
38 mm
8 3 mm
8 4 mm