Appendix D - Drawings; Appendice D - Disegni; Anhang D - Zeichnungen; Apéndice D - Dibujos - COMEM eSDB-10C Bedienungsanleitung

Appendix D - Drawings

1 2
eSDB10C 1 2
F
C
INLET/
OUTLET AIR
INLET/
OUTLET AIR
D
E
209 (8.22")
209 (8.22")
F
1 2
Figure 14
1 2
3
3
N°4 HOLES 14 (0.55")
N°4 HOLES 14 (0.55")
B
G
F
1
C
35 (1.37")
130 (5.12")
35 (1.37")
N°2 CABLE GLANDS A
TYPE M25x1.5
130 (5.12")
( 2:5)
N°2 CABLE GLANDS A
A
TYPE M25x1.5
( 2:5)
A
NOTES:
- MINIMUM CONNECTIONS METAL SHEET THICKNESS: 5mm
- ADVISED DIAMETER HOLE OF THE METAL
NOTES:
SHEET SUPPORT DEVICE: Ø13 mm
- FOR THE INSTALLATION FOLLOW THE
- MINIMUM CONNECTIONS METAL SHEET THICKNESS: 5mm
MANUAL INSTRUCTION
- ADVISED DIAMETER HOLE OF THE METAL
SHEET SUPPORT DEVICE: Ø13 mm
- FOR THE INSTALLATION FOLLOW THE
3
MANUAL INSTRUCTION
3
4 5
4 5
100
100
ANTIVIBRATION
DEVICE
30 (1.18")
ANTIVIBRATION
110 (4.33")
DEVICE
30 (1.18")
110 (4.33")
LAST REVISION
DESCRIPTION
MATERIAL
- - -
LAST REVISION
PROCESS
DESCRIPTION
- -
CREATED BY
MATERIAL
- - -
Diego Boro
PROCESS
APPROVED ON
- -
-
CREATED BY
COMPANY
Diego Boro
COMEM
APPROVED ON
RESPONSIBLE DEPARTMENT
-
ITABB-9AAE306693
COMPANY
COMEM
RESPONSIBLE DEPARTMENT
ITABB-9AAE306693
4 5
4 5
6
6
260.5 (10.25")
260.5 (10.25")
D
175.5 (6.91")
A
175.5 (6.91")
285.5 (11.24")
285.5 (11.24")
AGGIORNATO DISEGNO - Dreawing updated
TOLLERANZE GENERALI SECONDO - GENERAL TOLERANCES ACCORDING TO ISO 2768
AGGIORNATO DISEGNO - Dreawing updated
TOLLERANZE GENERALI SECONDO - GENERAL TOLERANCES ACCORDING TO ISO 2768
REVIEWED BY
-
DOCUMENT KIND
Assembly Drawing
REVIEWED BY
TITLE / SUPPLEMENTARY TITLE
-
COMEM ESDB10C
DOCUMENT KIND
-
Assembly Drawing
TITLE / SUPPLEMENTARY TITLE
DOCUMENT ID COMEM ESDB10C
NE-326
-
© COPYRIGHT ALL RIGHTS RESERVED
6
DOCUMENT ID
NE-326
© COPYRIGHT ALL RIGHTS RESERVED
6
7 8
7 8
REPLACED
REVISION
m
SCALE
WEIG
REPLACED
PART NUMBER
REVISION
-
m
SCALE
APPROVED BY
WEI
-
PART NUMBER
BASED ON DOC ID WORK ORDER ID PROJECT ID
-
IC0031
APPROVED BY
-
BASED ON DOC ID WORK ORDER ID PROJECT ID
IC0031
STATUS REV ITER
C
In Work
4
7 8
STATUS REV ITER
C
DRAWING SHEET ISO 5457: 1999-A3T
In Work
4
7 8
DRAWING SHEET ISO 5457: 1999-A3T
45
B
N
S
1