Working Instructions; Maintenance - Scheppach TPH900 Original Anleitungen

Change the handle position Fig. 10
Push the slide switch (13) to the stop.
At the same time you can switch between 5 different
position (-90°, -45°, 0°, 45°,90°).If you find the right po-
sition release the slide switch (13).
Starting of the hedge trimmer
Before starting the hedge trimmer you have to press
first the saftey switch (14). Secondly press the start le-
ver (15) for starting. For tunr off the deivce, release

8. Working instructions

Working with hedge trimmer
• The hedge trimmer may be used only for cutting hedges,
bushes and shrubs
• Hold the hedge trimmer with both hands on a safe
• distance from the body.
• The maximal diameter to cut depends on the wood's type,
age, moisture and hardness.
• Therefore cut very thick branches using branch shears to
your desired length before trimming the hedge.
• Due to its double sided knives the hedge trimmer can be
guided forward and backward or by oscillating movements
from one to another side.
• At first cut the sides of the hedge and then the upper
edge.
• Cut the hedge from the bottom up.
• Cut the hedge in trapezium shape.
• Stretch a guide over the complete length of the hedge
when you want to shorten the upper edge of the hedge
evenly.
• Trim in several passes if you have to cut down a large
portion of the hedge.
• Remove unconditionally any foreign objects out of the
hedge (e.g. wires) as these can damage the knives of the
hedge trimmer.
Best time for hedge trimming:
• Leaved hedge: June and October
• Conifer hedge: April and August
• Quickly growing hedge: from May and then every 6
weeks
Pay attention to breeding birds in the hedge. If so, put off
hedge trimming or leave this area out.
Oil the blades and the angle adjustment each time before
starting work, with environmentally friendly lubricant.
Regularly oil the blades during working hours as well.
Warning! Oil the tool only when the motor has been turned
off.
CAUTION: Incorrect use and misuse can damage the bush
cutter and cause severe injuries because of pieces hurled
away.
To minimize the risk of accidents by use of the cutting blade,
take note of following points:
• Never cut shrubbery or wood whose diameter is larger
than 2 cm.
• Avoid contact with metal bodies, stones, etc.
• Periodically check the cutting blade for damages. Never
continue to use a damaged cutting blade.
24 GB
Heruntergeladen von manualslib.de
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Handbücher-Suchmachiene
• When the cutting blade becomes apparently blunt, it must
be sharpened according to instructions. When the cutting
blade is apparently out of balance, it must be replaced.

9. Maintenance

NJURY WARNING!
Before working on the device, disconnect the mains
cable from the socket.
Always wear protective gloves when working on or
around cutting tools.
• Regularly check the device before starting work.
• Damaged blades have to be repaired or replaced by
an authorised service department before you can work
with the device.
• Clean the blades with a soft brush after working with
the device and spray a thin layer of liquid protective oil
on the whole blade.
• Always keep the ventilation holes in the motor casing
free and clean.
• Never use water to clean or spray the device. Clean
the motor casing with a damp cloth and never use de-
tergents or solvents! This may damage the device's
plastic parts. Dry the motor casing carefully afterwards.
• Always store the machine with the supplied protective
cover.
• Only use OEM parts for maintenance work. Using parts
other than original parts can cause damage to the ma-
chine.
Check the hedge trimmer for obvious faults such as:
– loose attachments
– worn or damaged components
– bent, broken or damaged cutting tools
– correctly attached and working covers and safety
devices
– wear, in particular, cutting tool play
Immediately replace damaged or blunt cutting tools,
even in the event of minor damage.
Wear Parts
Even when used in the intended way, some components
are subject to normal wear. They have to be replaced
depending on the kind of duration of usage. These parts
include, among others, the cutting tool and the retaining
disk.
m Warning! Use only original manufacturer's replace-
ment parts, accessories and attachments. Failure to do
so can cause poor performance, possible injury and may
void your warranty
Important hint in case of sending the equipment to a
service station:
Due to security reasons please see to it that the equipment
is sent back free of oil and gas!