Technical Data; Before Starting The Equipment; Attachment And Operation; Electrical Connection - Scheppach HC06 Originalbetriebsanleitung

6. Technical Data

Mains connection
Motor rating W
Operating mode
Compressor speed
Pressure vessel capacity
(in liters)
Operating pressure
Theoretical intake capacity
(l/min)
Sound power level LWA
Uncertainty KWA
Protection type
Weight of the unit in kg
Max. altitude
(above mean sea level)
The noise emission values were measured in ac-
cordance with EN ISO 3744.
Wear hearing protection.
The effects of noise can cause a loss of hearing.

7. Before starting the equipment

Before you connect the equipment to the mains sup-
ply make sure that the data on the rating plate are
identical to the mains data.
• Check the equipment for damage which may have
occurred in transit. Report any damage immedi-
ately to the transport company which was used to
deliver the compressor.
• Install the compressor near the point of consumption.
• Avoid long air lines and supply lines (extension
cables).
• Make sure that the intake air is dry and dustfree.
• Do not install the compressor in a damp or wet
room.
• The compressor may only be used in suitable
rooms (with good ventilation and an ambient tem-
perature from +5 °C to 40 °C). There must be no
dust, acids, vapors, explosive gases or inflamma-
ble gases in the room.
• The compressor is designed to be used in dry
rooms. It is prohibited to use the compressor in
areas where work is conducted with sprayed water.

8. Attachment and operation

8.1 Mains connection
• The compressor is equipped with a mains cable
with shock-proof plug. This can be connected to
any 230V~ / 50 Hz shock-proof socket which is
protected by a 16 A fuse.
• Before you use the machine, make sure that the
mains voltage is the same as the operating voltage
(see the rating plate).
Heruntergeladen von manualslib.de
220 - 240 V ~ / 50 Hz
1200
S1
3450 min-1
approx. 8 bar
approx. 192
96 dB(A)
3 dB
IP40
9.7
1000 m
Handbücher-Suchmachiene
• Long supply cables, extensions, cable reels etc.
cause a drop in voltage and can impede motor
start-up.
• At low temperatures below +5 °C, sluggishness
may make starting difficult or impossible.
8.2 On/off switch (fig. 2)
• The compressor is switched on by setting the
6
switch (15) to position I.
• The compressor is switched off by setting the
switch (15) to position 0.
8.3 Pressure adjustment: (fig. 1)
• YThe pressure at the manometer (5) can be ad-
justed with the pressure regulator (7).
• The pressure set can be utilised by connecting to
the quick-coupling (6).
8.4 Setting the pressure switch
• The pressure switch is set at the factory.
Cut-in pressure approx. 6 bar.
Cut-out pressure approx. 8 bar.
8.5 Using the tyre inflater
The compressed air tyre inflation device (13) is used
to inflate car tyres. With the corresponding accesso-
ries it can also be used to inflate and regulate bicycle
tyres, inflatable dinghies, air mattresses, balls etc.
Pressure can be released by actuating the vent
valve.
Important! The manometer has not been officially
calibrated!
After inflating, please check the air pressure with a
calibrated device.
8.6 Using the air blow gun
You can also use the air blow gun (12) to clean out
cavities and to clean soiled surfaces and work equip-
ment.
Always wear protective goggles when doing so!
8.7 Using the adapter set
The adapter set enables you to use the following ad-
ditional capabilities of the tyre inflation device:
Pumping up balls with the help of the ball needle (9).
The valve adapter (10) enables bicycle tyres to be
inflated.
Filling pools, air mattresses or boats with the help of
the additional adapter (11).

9. Electrical connection

The electrical motor installed is connected and
ready for operation. The connection complies
with the applicable VDE and DIN provisions. The
customer's mains connection as well as the ex-
tension cable used must also comply with these
regulations.
GB 75