Program Version; Overview Of Changes; Communication Objects - Niko SWISS GARDE 300 Applikationsbeschreibung

5. PROGRAMMVERSION 2.7
With the program version 2.7, the function possibilities of the presence detector - series Swiss Guard 360P KNX / KLR RA / EA expanded and existing features of program version 2.4, have been supplemented respectively adapted.
The standard values (default values) of the parameters compared to the settings in version 2.4 are partially modified.
These settings allow a simple and safe functionally check (initial start-up ) of the presence detector .
Older devices of software version 2.4 can also be programmed with the program version 2.7 ( backward compatibility ) .
However, supplemented functions and the additional communication objects are not all
supported.
5.1. Overview of the changes:
• Forced control Slave-Mode
• Parameter changes via communication objects
• Dimming function with constant light control (clc)
• Power on characteristics
• Automatic lighting OFF threshold
• Delay time in semi-automatic mode
• Standby-function
• Light sensor adaption

5.2. Communication objects

input objects
output objects
Object Function
0 Output - light (preset dimming)
0 Output - light (switching)
0 Output - light (scene)
1 Input external switch / status - light
(switching)
2 Input external motion - light (switching)
3 Input - light (forced control)
3 Input - light (lock)
4 Output - HVAC (switching)
5 External switch / status - HVAC (switching)
6 External motion - HVAC (switching)
7 Input - HVAC (forced control)
7 Input - HVAC (lock)
8 Threshold switch brightness (switching)
9 Brightness (lux value)
10 AD calibration value
16 Constant light control, switch on/off
17 Constant light control, dimming relative
18 Constant light control, preset dimming
20 Constant light control, forced control
21 Constant light control, scene selection
22 Constant light control, channel 1 - output
23 Constant light control, channel 2 - output
24 Light - standby
5.2.1. COMMUNICATION OBJECTS with SLAVE- Mode
Object Function
0 Output (switching)
3 Input (forced control)
Object forced control:
The object 3 as a forced control object knows 2 values ( 1 bit command ) which can be received :
If object forced control = 1: output ( Obj.0 ) remains locked when motion is detected , no telegrams are sent
If object forced control = 0: output ( Obj.0 )
2524X_2525XCH_ETS_description
see 5.2.0
see 5.2.1
see 5.2.2
see 5.3.1
see 5.3.2
see 5.3.3
see 5.3.4
see 5.3.5
link application with
light group actuator
light group actuator.
light group actuator
KNX switch, touch display, logic
Output - light for slave unit (object 0)
• External logic module
KNX switch, touch display, logic module
• Actuators for HVAC devices such as heating, ventilation and air conditioning
• Control of alarm logic modules
• Presence function
KNX switch, touch display, logic
Output HVAC for slave unit (output object 4).
External logic module
KNX switch, touch display, logic
Logic, actuator
Logic, touch display
Read out and then set manually for calibration procedure
KNX switch , logic
4 bit dimming object from KNX switch for ON/OFF, dimming up and down, touch display
Logic module
KNX button, logic
Logic module
Dimming actuator for light group 1
Dimming actuator for light group 2
Switching of standby value sets
link application with
Master presence -detector
KNX switch, touch display, logic module
AUTO ( normal operation )
2524X/2525XCH
Bit/Byte
1 byte
1 bit
1 bit
1 bit
1 bit
2 bit
1 bit
1 bit
1 bit
2 byte
2 bit
1 bit
1 bit
2 byte
2 byte
1 bit
4 bit
1 byte
1 bit
1 byte
1 byte
1 byte
1 bit
Bit/Byte
1 bit
1 bit
15
EN