Package Contents; Description (Fig. A) - DeWalt D21570 Originalanweisung

Markings on Tool
The following pictograms are shown on the tool:
a
Read instruction manual before use.
g
Wear ear protection.
f
Wear eye protection.
Date Code Position (Fig. B)
10
The date code , which also includes the year of manufacture,
is printed into the housing.
Example:
2020 XX XX
Year and week of Manufacture

Package Contents

The package contains:
1 Rotary drill
1 Side handle
1 Depth Rod (DWD530 and D21570)
1 Chuck Key (D21570K only)
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Description (Fig. A)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
1 Trigger switch
2 Reversing lever
3 Side handle
4 Chuck
5 Indicator light
6 Main handle
7 Lock-on button
8 Speed/mode selector collar
9 Chuck key
10 Date code
Intended Use
This heavy-duty drill is designed for professional drilling and
impact drilling applications.
DO nOt use under wet conditions or in the presence of
flammable liquids or gases.
This heavy-duty drill is a professional power tool.
DO nOt let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Young children and the infirm. This appliance is not
•
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
Side Handle (Fig. C)

WARNING: To reduce the risk of personal injury,
ALWAYS operate the tool with the side handle properly
installed and tightened. Failure to do so may result
in the side handle slipping during tool operation and
subsequent loss of control. Hold tool with both hands to
maximise control.
3
A side handle is supplied with your drill. The side handle
clamps to the front of the gear case and can be rotated 360
degrees to permit right- or left-hand use.
After the side handle is rotated into position, it should be
pushed rearward until the slots
are aligned and fully engaged with the projecting tabs
the underside of the gear case. The side handle is then securely
clamped by turning clockwise until tight.
Torque Limiting Clutch
This tool is equipped with a torque limiting clutch that reduces
the maximum torque reaction transmitted to the operator in
case of jamming of a drill bit. This feature also prevents the
gearing and electric motor from stalling. The torque limiting
clutch has been factory-set and cannot be adjusted.
E-CLUTCH Anti-Lock Control™ (Fig. B)
D21570, DWD530
Your D WALT drill may come with an electronic feature called
e
E-CLUTCH Anti-Lock Control™. It is designed to help you control
the drill during a stall and keep it from pulling out of your hands.
This may be encountered when drilling in steel or using large
bits in wood.
As a stall situation presents itself, the motor cycles on and off
for a set period of time. This reduces the reaction of the stall and
allows you to keep the drill under control. Releasing the trigger
resets the E-Clutch and the unit will operate in normal mode
when the trigger is depressed again.
The E-CLUTCH Anti-Lock Control™ also incorporates an overload
protection feature designed to help prevent the unit from
becoming too hot during high load applications.
If the unit becomes excessively hot during operation this feature
will cut the motor, The feature will continue to cut the motor
if it is restarted and placed under a high load before it has
cooled off.
EngLIsh
3
on the lip of the side handle
12
on
19