Symbols And Their Meaning - Bosch GTS 18V-216 Professional Betriebsanleitung

34 | English
Only use saw blades that match the specifications
u
given in this operating manual and that are tested and
marked in accordance with EN 847-1
Only use saw blades that are recommended by the
u
power tool manufacturer and are suitable for using on
the material you want to saw.
Only advance the workpiece towards the saw blade
u
when it is running. Otherwise there is a risk of kickback
occurring if the saw blade catches in the workpiece.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Symbols
The following symbols may be important for the operation of
your power tool. Please take note of these symbols and their
meaning. Correctly interpreting the symbols will help you to
operate the power tool more effectively and safely.

Symbols and their meaning

Keep hands away from the cutting area
while the power tool is running. Con-
tact with the saw blade can lead to injur-
ies.
Wear a dust mask.
Wear hearing protection. Exposure to
noise can cause hearing loss.
Wear safety goggles.
1 609 92A 5HL | (11.09.2020)
Symbols and their meaning
3 601 M44 000 Observe the dimensions of the saw
blade. The hole diameter must match the
3 601 M44 040
tool spindle without play. If it is neces-
sary to use reducers, ensure that the di-
mensions of the reducer are suitable for
the base blade thickness and the saw
3 601 M44 0B0
blade hole diameter, as well as the tool
Ø 25,4 mm
spindle diameter. Wherever possible, use
the reducers provided with the saw
Ø 216 mm
blade.
The saw blade diameter must match the
information specified on the symbol.
3 601 M44 000 a The saw blade must be no more than
3 601 M44 040 216 mm in diameter.
b When changing the saw blade, make
b
a
sure that the cutting width is no smaller
d
than 1.7 mm and the base blade thick-
c
ness is no larger than 1.5 mm. Other-
wise, there is a risk that the riving knife
will hook into the workpiece.
c The riving knife is 1.6 mm thick.
d The cutting direction of the teeth (dir-
ection of the arrow on the saw blade)
must match the direction of the arrow on
the riving knife.
3 601 M44 0B0 a The saw blade must be no more than
216 mm in diameter.
b a
b When changing the saw blade, make
d
sure that the cutting width is no smaller
c
than 2.3 mm and the base blade thick-
ness is no larger than 2.1 mm. Other-
wise, there is a risk that the riving knife
will hook into the workpiece.
c The riving knife is 2.2 mm thick.
d The cutting direction of the teeth (dir-
ection of the arrow on the saw blade)
must match the direction of the arrow on
the riving knife.
3 601 M44 000 The riving knife is 1.6 mm thick.
3 601 M44 040
The maximum possible workpiece height
is 70 mm.
3 601 M44 0B0 The riving knife is 2.2 mm thick.
The maximum possible workpiece height
is 70 mm.
Left-hand side:
Indicates the direction of rotation of the
crank for lowering (transport position)
Bosch Power Tools