Makita DJS200 Betriebsanleitung Seite 7

NOTE: Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
NOTE: The first (far left) indicator lamp will blink when
the battery protection system works.
Tool / battery protection system
The tool is equipped with a tool/battery protection sys-
tem. This system automatically cuts off the power to
extend tool and battery life. The tool will automatically
stop during operation if the tool or battery is placed
under one of the following conditions:
Overload protection
This protection works when the tool is operated in a
manner that causes it to draw an abnormally high cur-
rent. In this situation, turn the tool off and stop the appli-
cation that caused the tool to become overloaded. Then
turn the tool on to restart.
Overheat protection
When the tool or battery is overheated, the tool stops
automatically and the lamp blinks. In this case, let the
tool and battery cool before turning the tool on again.
Overdischarge protection
This protection works when the remaining battery
capacity gets low. In this situation, remove the battery
from the tool and charge the battery.
Switch action
CAUTION:
Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
To prevent the switch trigger from accidentally pulled,
the trigger-lock button is provided.
To start the tool, depress the trigger-lock button from "B"
side and pull the switch trigger.
Tool speed is increased by increasing pressure on the
switch trigger. Release the switch trigger to stop. After
use, always press in the trigger-lock button from "A"
side.
For continuous operation, pull the switch trigger and
then push in the lock button. To stop the tool from the
locked position, pull the switch trigger fully to unlock.
► Fig.3: 1. Trigger-lock button 2. Switch trigger
3. Lock button
Accidental re-start preventive
function
Even if you install the battery cartridge while pulling the
switch trigger, the tool does not start.
To start the tool, first release the switch trigger and then
pull the switch trigger.
Lighting the lamp
CAUTION:
Do not look in the light or see the
source of light directly.
To turn on the lamp, slightly pull the switch trigger, and
then release it. The lamp goes out approximately 10
seconds after releasing the switch trigger.
► Fig.4: 1. Lamp
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Removing and installing shear
blades
CAUTION:
Never remove the blades with bare
hands. Wear gloves.
The sharp edge of the blade may cause injury.
Removing cutting head
Use the hex wrench (5/32") to loosen the bolts which
secure the cutting head. Pull the cutting head straight
out by turning it left and right alternately.
► Fig.5: 1. Cutting head 2. Bolt 3. Hex wrench (5/32")
4. Loosen
Removing shear blades
NOTICE:
Hold the blades and the sleeve not to fall
from the cutting head.
NOTICE:
Be careful not to lose the sleeve.
Remove the bolts which hold the blades. Then the
blades can be removed easily.
► Fig.6: 1. Bolt 2. Side blade L 3. Center blade
4. Side blade R 5. Sleeve
Installing shear blades
Insert the center blade, the side blade L, the side blade
R, and the sleeve into the cutting head.
Tighten the bolts. In this process, the bolt heads should
be protruding 2 - 3 mm from the cutting head surface.
If you tighten the bolts excessively, the cutting head
cannot be installed to the tool.
► Fig.7: 1. Cutting head 2. Side blade R 3. Center
blade 4. Sleeve 5. Sleeve 6. Side blade L
7. Bolt
7 ENGLISH