urmet domus Genya 1072 Bedienungsanleitung Seite 10

MINIMUM CONVERSATION TIME (BUSY)
When a user is called and answers the door phone, all other call stations will be busy for the minimum
programmed conversation time. A communication that has just started cannot be interrupted. All devices in
the system must have the same minimum conversation time (busy time).
Letter "O" identities the off-hook waiting time:
• 10s busy: O1 ↵
• 20s busy: O2 ↵
• 30s busy: O3 ↵
• 40s busy: O4 ↵
DOOR LOCK ACTIVATION TIME
The relay controlling the door lock can be managed in pulse mode (approximately 600 ms) or stabile mode
(from 1 to 30 s).
Letter "D" identities the lock activation time:
• Pulse: D00 ↵
• Door lock xy seconds: Dxy ↵
The name tag light LEDs will go out when then electrical lock is operated.
CODE BUTTON ASSOCIATION
This is the step in which user codes to be programmed are associated to each button connected to the
digitiser. The call code sequence is: CxyzwPnm ↵
where xyzw is the user code and nm is the calling station button number.
The user code xyzw can have the following values:
• 0001-9999 for numeric code formats
• x000-x999 for alphabetic prefi x code formats (x from A to J)
• 000x-999x for alphabetic suffi x code formats (x from A to J)
• 0000 for direct calls to switchboard in day mode
• LLLL for "staircase lights" function
Connect a door unit module with 4 button Ref. 1128/44 or Ref. 1128/45 and up to three 10 button modules
Ref. 1082/40 or Ref. 1082/41 to the door unit. The button number nm depends on the position of the terminal
to which it is connected according to the following table:
1÷4: door unit module Ref. 1128/44 or Ref. 1128/45
5÷14: fi rst buttons module Ref. 1082/40 or Ref. 1082/41
15÷24: second buttons module Ref. 1082/40 or Ref. 1082/41
25÷34 third buttons module Ref. 1082/40 or Ref. 1082/41
Once a code is programmed, press button ↵ to automatically program call code xyzw+1 on button nm+1. For
example, the calling sequence C1000P01↵↵↵ will program code 1000 on button 01, code 1002 button 02
and code 1002 on button 03.
1st edition system: this programming is not required.
Programming door phones in 2nd edition systems using the programming adapter
The door phone programming sequence consists of two steps:
A. Door phone booking (to be made on a calling station).
B. Door phone programming (to be made in the apartments).
A: Door phone booking.
1. Insert adapter 1072/60 in the specifi c minidin connector.
2. Press the user buttons to be associated with the door phones once. The booking sequence according
to which the buttons are pressed must be the same as the order in which the operator will go to the
apartments. DO NOT press the switchboard call button or the "staircase lights" function.
3. A beep will be heard after 30 seconds from last pressing a user button (end of booking).
18
B: Door phone programming.
1. Go to the fi rst booked user, hold the button pressed and lift the door phone handset. Two confi rmation
beeps will be heard and the LED will fl ash to indicate that it has been programmed.
2. Go to the other booked users and repeat the operations.
Refer to the attached sheet to remember the code/button association sequence.
Associating 2/3 door phones in parallel in 2nd edition systems using the programming adapter
To install two or three door phones in one apartment and make them both ring when a call is received, press
the button related to the user twice or three times with the door phones in parallel when booking the door
phones.
When you reach the apartment where the parallel door phones are installed according to the programming
sequence, repeat the programming sequence on both door phones.
Adding new users in 2nd edition systems using the programming adapter
Insert the programming adapter in the digitiser connector and program the user code of the button which will
call the unit. Press this button to book programming and go to the user to program the door phone.
Programming door phones in 1st edition systems using the programming adapter
The door phone programming sequence consists of two steps:
A. Door phone booking (to be made on a calling station).
B. Door phone programming (to be made in the apartments).
A: Door phone booking.
1. Insert adapter 1072/60 in the specifi c minidin connector.
2. Press the user buttons to be associated with the door phones once. The booking sequence according
to which the buttons are pressed must be the same as the order in which the operator will go to the
apartments.
3. A beep will be heard after 30 seconds from last pressing a user button (end of booking).
4. Leave the adapter 1072/60 in the digitiser and go to the apartments to program the door phones.
B: Door phone programming.
1. Go to the fi rst booked user, hold the button pressed and lift the door phone handset. Two confi rmation
beeps will be heard and the LED will fl ash to indicate that it has been programmed.
2. Go to the other booked users and repeat the operations.
Refer to the attached sheet to remember the code/button association sequence.
DS1072-031 DS1072-031
19