m-e VISTUS AD Betriebsanleitung Seite 17

The optical signal (surround light on the talk and door opener button)
remains active, even then the ring tone/melody is deactivated and still
rings. The red LED flashes if the bell is rung while the mute is activated.
NOTE: If the VTX-BELL module is used then this will also be deactivated
in the silent mode, i.e. the connected receivers will not give a
signal either.
IMPORTANT: The indoor station needs to be activated for the
following settings (e.g. by pressing the talk button). Otherwise it is not
possible to set the talk/volume, and melody.
Speaking volume
The two side buttons (B. 12 and 13) can be used to set the speaking
volume in several steps. Button 12 is used to increase the volume and
button 13 to reduce it.
Melody selection
The next melody is played every time you press the
(B/C.11). The last melody to be played is automatically stored.
Own melody on memory card
This intercom system offers the possibility to select your own ringtones,
which are stored in MP3 or WAV format on a micro SD card. The memo-
ry card must be formatted with FAT32. You store your ringtones directly
on the SD card (without using folders), a maximum of 16 different
ringtones can be stored on the SD card. Insert the prepared SD card into
the SD card slot (B.16) on the board. The ringtones on the memory card
replace the internal ringtones. When the memory card is removed, the
internal melodies are available again.
STARTUP
Once all the components have been fitted and connected, switch on
the operating voltage. Depending on the type of installation, either
plug the mains adapter into a suitable socket or switch on the circuit
breaker that is connected to the DIN rail power supply unit. Ring the
external unit once to initialise the system (if multiple external units are
installed, each external unit must be rung once).
NOTE: Switch the operating voltage off again before carrying out any
work on the system!
OPERATION (as door intercom system)
1. Press the bell button.
2. The stored ring tone will play on the corresponding
indoor station(s)
VISTUS AD-400 I-M 210x240 2019 Fin19.indd 17
3. Accept the conversation on the indoor unit by pressing briefly on
the talk button ( ).
4. If a door opener is connection then you can activate it by briefly
pressing the door opener button ( ). The bell button will light
green for the duration of the door opener as confirmation.
5. Press the talk button ( ) briefly in order to switch the system
back to standby operation.
Note: If a floor button is connected then an unchangeable ring tone
is played when the floor button is activated. This ring tone is fixed
and is not included in the 'normal' tones/melodies to make it easy to
differentiate.
OPERATION (as internal house intercom)
All indoor units that are connected to the same bell button can also be
used as an internal intercom.
button
1. Press the internal button
which you wish to reach another indoor station. All the connected
indoor station will ring. No image will be shown.
2. To accept the conversation on one of the other connected indoor
stations you need to briefly press the talk button there (B. 6).
3. The talk button needs to be pressed briefly on one of the two
indoor stations in order to end the conversation.
Note: It is not possible to set different ring tones for internal and
external calls.
Technical data:
Outdoor station
Operating voltage: 15V DC
Standby power: <0.5W
Connection for door opener: Relay contact; max. load capacity 15V/1A
Bell button illumination: automatic via CDS sensor
Indoor station
Operating voltage: 15V DC
Standby power: <0.5W
NOTES
The functionality of the unit can be affected by the influence of strong
static, electrical or high frequency fields (discharging, mobile phones,
radios, microwaves).
17 17
ENGLISH | VISTUS-AD
(B. 7) on the indoor station from
GB
05.12.19 15:59