Ec Declaration Of Conformity; General Power Tool Safety Warnings - Makita DTM40 Bedienungsanleitung

Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841:
Work mode: Sanding
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode: Cutting with plunge cut saw blade
Model DTM40
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model DTM50
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode: Cutting with segmental saw blade
Model DTM40
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model DTM50
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode: Scraping
Model DTM40
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model DTM50
Vibration emission (a
Uncertainty (K) : 1.5 m/s
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during
actual use of the power tool can differ from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).

EC Declaration of Conformity

For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.

General power tool safety warnings

WARNING:
Read all safety warnings, instruc-
tions, illustrations and specifications provided
with this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
2
) : 2.5 m/s or less
h
2
2
) : 9.5 m/s
h
2
2
) : 10.0 m/s
h
2
2
) : 5.0 m/s
h
2
2
) : 5.5 m/s
h
2
2
) : 7.5 m/s
h
2
2
) : 9.5 m/s
h
2
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
CORDLESS MULTI TOOL SAFETY
WARNINGS
1. This power tool is intended to function for
sawing, cutting, grinding and sanding. Read all
safety warnings, instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
2. Hold power tool by insulated gripping sur-
faces, when performing an operation where the
cutting accessory may contact hidden wiring.
Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
3. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
4. Always use safety glasses or goggles. Ordinary
eye or sun glasses are NOT safety glasses.
5. Avoid cutting nails. Inspect workpiece for any
nails and remove them before operation.
6. Hold the tool firmly.
Make sure the application tool is not contacting
7.
the workpiece before the switch is turned on.
8. Keep hands away from moving parts.
9. Do not leave the tool running. Operate the tool
only when hand-held.
10. Always switch off and wait for the blade to
come to a complete stop before removing the
blade from the workpiece.
11. Do not touch the application tool or the work-
piece immediately after operation; they may be
extremely hot and could burn your skin.
12. Do not operate the tool at no-load unnecessarily.
13. Always use the correct dust mask/respirator for
the material and application you are working with.
14. Some material contains chemicals which may
be toxic. Take caution to prevent dust inhala-
tion and skin contact. Follow material supplier
safety data.
15. This tool has not been waterproofed, so do not
use water on the workpiece surface.
16. Ventilate your work area adequately when you
perform sanding operations.
17. Use of this tool to sand some products, paints
and wood could expose user to dust contain-
ing hazardous substances. Use appropriate
respiratory protection.
18. Be sure that there are no cracks or breakage
on the pad before use. Cracks or breakage
may cause a personal injury.
19. Do not use accessories which are not specifically
designed and recommended by the tool manufac-
turer. Just because the accessory can be attached to
your power tool, it does not assure safe operation.
5 ENGLISH