Makita DTM40 Bedienungsanleitung Seite 4

ENGLISH (Original instructions)
SPECIFICATIONS
Oscillation per minute
Oscillation angle, left/right
Overall length
Rated voltage
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
Charger
• Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.
Intended use
The tool is intended for sawing and cutting wood,
plastic, gypsum, non-ferrous metals, and fastening
elements (e. g. unhardened nails and staples). It is also
intended for working soft wall tiles, as well as dry sand-
ing and scraping of small surfaces. It is especially for
working close to edge and flush cutting.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841:
Work mode: Sanding
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
Work mode: Cutting with plunge cut saw blade
Model DTM40
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
Model DTM50
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
Work mode: Cutting with segmental saw blade
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
Model
Net weight
D.C.14.4 V Model
D.C.18 V Model
) : 78 dB (A)
pA
) : 82 dB (A)
pA
) : 93 dB (A)
WA
) : 84 dB (A)
pA
) : 95 dB (A)
WA
) : 81 dB (A)
pA
) : 92 dB (A)
WA
DTM40
6,000 - 20,000 (min
1.7 - 2.0 kg
D.C. 14.4 V
BL1415N / BL1430 / BL1430B / BL1440 / BL1450 / BL1460B
BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /
BL1840B / BL1850 / BL1850B / BL1860B
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF
Work mode: Scraping
Model DTM40
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
Model DTM50
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
4 ENGLISH
DTM50
-1
)
1.6 ° (3.2 ° total)
307 - 324 mm
1.8 - 2.2 kg
D.C. 18 V
) : 81 dB (A)
pA
) : 92 dB (A)
WA
) : 83 dB (A)
pA
) : 94 dB (A)
WA