Harman AKG IVM 4 Bedienungsanleitung Seite 34

S S e e l l e e c c t t i i n n g g M M o o d d e e s s : :
3 3 . . 5 5 . . 5 5 P P o o w w e e r r i i n n g g D D o o w w n n
3 3 . . 5 5 . . 6 6 S S e e l l e e c c t t i i n n g g t t h h e e
C C o o u u n n t t r r y y P P r r e e s s e e t t
Refer to fig. A6
on page 126.
N N o o t t e e : :
3 3 . . 5 5 . . 7 7 S S e e l l e e c c t t i i n n g g
F F r r e e q q u u e e n n c c i i e e s s f f r r o o m m t t h h e e
P P r r e e s s e e t t S S c c r r e e e e n n
Refer to fig. A6
on page 126.
3 3 . . 5 5 . . 8 8 S S e e l l e e c c t t i i n n g g
F F r r e e q q u u e e n n c c i i e e s s f f r r o o m m t t h h e e
F F r r e e q q u u e e n n c c y y S S c c r r e e e e n n
Refer to fig. A7
on page 127.
3 3 . . 5 5 . . 9 9 S S e e t t t t i i n n g g R R F F O O u u t t p p u u t t
Refer to fig. A6
on page 126.
N N o o t t e e : :
3 3 . . 5 5 . . 1 1 0 0 N N a a m m i i n n g g t t h h e e
T T r r a a n n s s m m i i t t t t e e r r
Refer to fig. A8
on page 127.
3 3 . . 5 5 . . 1 1 1 1 S S e e t t t t i i n n g g I I n n p p u u t t
G G a a i i n n
Refer to fig. A9
on page 128.
34
3 Setting Up
• To toggle between LOCK and SETUP modes, hold down SETUP for about 2
seconds.
• Hold down the ON/OFF control until the display goes dark.
1. When you switch power to the transmitter on for the first time, the "NAME" label
and the name of the first programmed Preset will be flashing.
• In order to select the appropriate Preset for a specific country (e.g., on tour)
later on,
A: Switch power to the transmitter on and press SETUP while the frequency is
displayed in MHz,
OR
B: Switch power to the transmitter off and hold down SETUP for about 2 sec-
onds.
2. Turn SETUP CW or CCW to select the desired Preset (country code).
3. Press SETUP briefly. The transmitter will automatically indicate the first Sub-
channel ("CHANNEL") of the first Frequency Group in memory. The transmitter
is in SETUP mode so you can easily select a different frequency.
4. Continue with step 2 in section 3.5.7.
1. Switch the transmitter to SETUP mode.
2. If the display shows the frequency in MHz, briefly turn SETUP CCW to call up
the Preset screen.
3. Select a Frequency Group ("GROUP") and a frequency ("CHANNEL") within this
Group.
4. Select the RF OUTPUT level. (Refer to section 3.5.9.)
5. Save your setting ("SAVE—Y").
1. Switch the transmitter to SETUP mode.
2. If the display shows the Preset screen, briefly turn SETUP CCW to call up the
frequency screen.
3. You can select the frequency in 25 MHz increments.
4. Select the RF OUTPUT. (Refer to section 3.5.9.)
5. Save your setting ("SAVE—Y").
• You can select the transmitter's RF output level from the Preset screen (section
3.5.7) or the frequency screen (section 3.5.8) after having selected a frequency.
1. From the Preset or frequency screen, press SETUP briefly as many times as
needed to make the "RF OUTPUT" label flash.
2. Set RF output to the desired level between 10 mW and 100 mW. When "OFF"
is lit, no signal will be transmitted.
• The approved maximum RF output depends on local legislation. Therefore, you
can only choose from the legally approved values stored in each Preset.
3. Save your setting ("SAVE—Y").
The default transmitter name ("DEVICE") is "IVM—4".
• You can change this name at any time in SETUP mode, from the "DEVICE"
screen.
• The control range is -20 dB to +20 dB.
• To save the selected value, press SETUP briefly.
AKG IVM 4