Electrical Connection; Transport; Cleaning, Maintenance, Storage And Ordering Of Spare Parts; Exterior Cleaning - Scheppach SD1600V Original Bedienungsanleitung

5. After completing the inside cut, remove the saw
blade (21) from the blade holders (as described
in 8.1).
6. Remove the workpiece from the table.
9.6 Mitre cutting (fig. 14)
WARNING
Be especially careful when making mitre cuts. The
angle of the saw table makes it easier for the work-
piece to slip. There is a danger of injury.
1. To perform mitre cuts, adjust the distance be-
tween the saw blade guard (5) which is mounted
on the depressor (23) and the work table accord-
ingly.
2. Swivel the table by loosening the knurled nut (14)
and tilting the saw table (6) into the desired posi-
tion.
3. Tighten the knurled nut (14).

10. Electrical connection

The electrical motor installed is connected and
ready for operation. The connection complies
with the applicable VDE and DIN provisions.
The customer's mains connection as well as
the extension cable used must also comply with
these regulations.
Damaged electrical connection cable
The insulation on electrical connection cables is of-
ten damaged.
This may have the following causes:
• Pressure points, where connection cables are
passed through windows or doors
• Kinks where the connection cable has been im-
properly fastened or routed
• Places where the connection cables have been cut
due to being driven over
• Insulation damage due to being ripped out of the
wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insulation
damage.
Check the electrical connection cables for damage
regularly. Ensure that the connection cables are dis-
connected from electrical power when checking for
damage.
Electrical connection cables must comply with the
applicable VDE and DIN provisions.
Only use connection cables with the marking H 05
VV-F.
The printing of the type designation on the connec-
tion cable is mandatory.
28 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
AC motor
The mains voltage must be 220-240 V~.
Extension cables up to 25 m long must have a cross-
section of 1.5 mm .
2
Connections and repairs of electrical equipment may
only be carried out by an electrician.
Please provide the following information in the event
of any enquiries:
• Type of current for the motor
• Machine data - type plate

11. Transport

• Transport the electric tool by lifting it on the recess-
es provided for this on the frame and the engine
cover.
• Never use the protective devices for handling or
transport.
• Make sure that the exposed part of the saw blade
is covered during transport, e. g. by the protective
device.
12. Cleaning, maintenance, storage
and ordering of spare parts
WARNING
Always switch the machine off and remove the mains
plug prior to all maintenance and cleaning work.
12.1 Cleaning
Keep all safety devices, air vents and the motor hous-
ing free of dirt and dust as far as possible. We recom-
mend that you clean the equipment immediately after
you use it.

12.1.1 Exterior cleaning

• Clean the device at regular intervals using a damp
cloth and a little soft soap.
• Do not use cleaning agents or solvents; these may
be aggressive to the plastic parts in the equipment.
• Make sure that no water can penetrate the device
interior.
12.1.2 Interior cleaning (fig. 15)
1. Open the storage box (9).
2. Remove the screw (34).
3. Loosen the screw (33).
4. Remove the cover (8).
5. Blow out the device interior with low-pressure
compressed air.
6. Attach the cover again (8).
7. Fasten the screw (33).
8. Insert the screw (34) again and tighten it.
9. Close the storage box (9).