Cleaning And Maintenance; Optional Accessory - Redmond SkyCooker RMC-M226S-E Bedienungsanweisung

V. CLEANING AND MAINTENANCE
General Guidelines
• Prior to the first use or in order to remove the odour after cooking steam half a lemon for 15 minutes using the STEAM-
programme.
• Do not leave the cooking bowl with meals or liquids inside a closed multicooker for over 24 hours. Store cooked meals
in a refrigerator and reheat them when required, using the Reheat function.
• If not in use for long time, unplug the appliance. The cooking chamber, heating disc, cooking bowl, inner lid, steam valve,
safety valve, and condensation collector must be dry and clean.
• Before you start cleaning the appliance, make sure that it is unplugged and has completely cooled down. Use soft cloth
and mild soap to clean.
DO NOT use a sponge or tissue with hard or abrasive surface or abrasive pastes. Do not use any chemically aggressive sub-
stances or any other agents that are not recommended for cleaning items that contact food.
DO NOT immerse the appliance in water or wash under running water!
• Be careful when cleaning silicone parts of the multicooker, because damaged or deformed parts may lead to malfunction
of the unit.
Clean the housing when necessary. The cooking bowl, inner lid, removable steam valve, and safety valve need to be cleaned
after each use. Condensate, accumulating during cooking, needs to be removed after each use. Clean the interior of the
cooking chamber when necessary.
Cleaning the body
Clean the product body with a soft, damp kitchen cloth or sponge. It is possible to use a delicate cleaning agent. In order to
avoid the appearance of water stains and stains on the body, we recommend wiping its surface dry.
Cleaning the bowl
You can clean the bowl by hand, using a soft sponge and dishwashing detergent, or in the dishwasher (according to the
manufacturer's recommendations). If heavily dirty, fill the bowl with warm water and leave to soak for a while, then clean.
For more effective soaking, the bowl filled with cold water (not higher than the maximum permissible level) can be put
into the multicooker, close the lid and turn on the heating for 30-40 minutes. Be sure to clean the outer surface of the
bowl is dry before you put it in the body of the multicooker.
When the bowl is used regularly, it is possible to completely or partially change the color of the internal non-stick coating.
This in itself is not a sign of a defect.
Cleaning the steam valve
1. Gently pull the steam valve up and toward you.
2. Turn the inner lid counterclockwise until it stops and remove it.
3. If necessary, carefully remove the valve rubber. Flush all parts of the valve.
4. Assemble it in the reverse order: install the rubber seal into the place, align the grooves of the main part of the valve
with the corresponding protrusions on the inner casing and turn clockwise. Install the steam valve firmly into the
pocket on the appliance lid.
Condensate removal
The condensate collector on the appliance body should be cleaned after each use of the multicooker. Grasp the sides
of the container, pull it slightly towards you, remove it. Pour out the condensate; wash the container and replace it.
Sometimes excess condensate can accumulate in a special recess around the bowl on the appliance body. Use kitchen
wipes or a towel to remove it.
Cleaning the working chamber
If the instructions in this manual are strictly followed, the risk of liquid, food particles or debris entering the working
chamber of the appliance is minimal. If significant contamination does occur, the surfaces of the working chamber should be
cleaned to avoid incorrect operation or damage to the appliance.
Before you clean the working chamber of the multicooker, make sure that the device is disconnected from the mains and
completely cooled down!
The side walls of the working chamber, the surface of the heating disc and the casing of the central temperature sensor
(located in the middle of the heating disc) can be cleaned with a moistened (not wet!) sponge or napkin. If you use detergent,
it is necessary to carefully remove its residues to eliminate the appearance of an undesirable smell during subsequent
cooking.
If foreign bodies get into the recess around the central temperature sensor, carefully remove them with tweezers, without
pressing on the sensor housing. If the surface of the heating disc is dirty, it is permissible to use a moistened sponge of
medium hardness or a synthetic brush.
With regular use of the appliance over time, a complete or partial change in the color of the heating disc is possible. In itself,
this is not a sign of a malfunction of the appliance and does not affect the correctness of its operation.
Transportation and Storage
Before repeated operation or storage completely dry all parts of the appliance. Store the assembled appliance in a dry,
ventilated place away from heating appliances and direct sunlight.
During transportation and storage, do not expose the device to mechanical stress, that may lead to damage of the device
and/or violation of the package integrity.
Keep the device package away from water and other liquids.
VI. OPTIONAL ACCESSORY
Additional accessories are not included in the delivery package of the multicooker. You can buy them, as well as learn about
new products from REDMOND on the website www.redmond. company or in the shops of official dealers.
VII. BEFORE CONTACTING THE SERVICE CENTER
Problem Possible cause
The error message System error (possible failure of the elec-
E1–E4 appeared on tronic board or thermal sensors) or loosely
the display closed lid
The error message E5
Automatic overheating protection has been
appeared on the dis-
activated
play
Power cord is not connected to the appliance
and/or socket
Appliance does not
Wall socket is not working properly
switch on
Power supply failure
Power supply interruption (power supply is
unstable/underrated)
There is a foreign object between the bowl
and the heating element (grain, food particles,
Dish is taking too
debris, etc.)
long to cook
The bowl is not properly positioned
Heating disk is dirty
SkyCooker RMC-M226S-E GBR
FRA
DEU
ITA
ESP
PRT
DNK
NOR
SWE
FIN
LTU
LVA
EST
ROU
Solution
HUN
Close the lid tightly. If the problem persists, contact
HRV
an authorized service center
SVK
Do not operate the appliance with an empty bowl!
Disconnect the appliance from the mains, let it cool
SVN
for 10-15 minutes, then add water (broth) to the bowl
and continue cooking. If the problem persists, contact
an authorized service center
CZE
Ensure that the power cord is connected to the cor-
responding inlet on the housing of the appliance and
POL
to the socket
SRB
Connect to a properly working wall socket
Check the power supply. If not available, contact local
GRE
electricity supply company
BGR
Ensure that the power supply is stable. If unstable /
underrated, contact local electricity supply company
RUS
Unplug the appliance and let cool down. Remove
foreign object or objects
UKR
Properly position the bowl into place
Unplug the appliance and let cool down. Clean heat-
ing disk
11