Makita DA001G Betriebsanleitung Seite 9

Speed change
NOTICE:
Use the speed change knob only after
the tool comes to a complete stop. Changing the
tool speed before the tool stops may damage the tool.
NOTICE:
Always set the speed change knob
carefully into the correct position. If you operate
the tool with the speed change knob positioned half-
way between the position 1 and the position 2, the
tool may be damaged.
Two speed ranges can be preselected with the speed
change knob.
To change the speed, depress the lock button and turn
the speed change knob so that the pointer points to the
position 1 for low speed or the position 2 for high speed.
► Fig.8: 1. Lock button 2. Pointer 3. Speed change
knob
Torque limiter
The torque limiter will actuate when a certain torque
level is reached at the low speed setting (position 1).
The motor will disengage from the output shaft. When
this happens, the tool bit will stop turning.
To restart the tool, lift the tool bit out of the workpiece
and then pull the switch trigger again.
Electronic function
Electric brake
This tool is equipped with an electric brake. If the tool
consistently fails to quickly cease to function after the
switch trigger is released, have the tool serviced at a
Makita service center.
Soft start feature
This function allows the smooth start-up of the tool by
limiting the start-up torque.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing side grip (auxiliary handle)
CAUTION:
Always be sure that the side grip is
installed securely before operation.
Screw the side grip on the tool securely. The side grip
can be installed on either side of the tool, whichever is
convenient.
► Fig.9: 1. Side grip
Front handle
CAUTION:
Do not fix the front handle beyond the
limits of the arrow as illustrated. Be cautious that your
hand is not caught in the grip. Keep the hand away
from the drill chuck. They can lead to serious accidents.
CAUTION:
Always be sure that the hex bolts
(both sides) of the front handle are tightened securely.
The front handle can be installed in any position within
0° - 112.5° as illustrated.
► Fig.10: 1. Front handle
To change the position, loosen the hex bolts (both
sides) with a hex wrench and turn the front handle to the
desired position. Then tighten the hex bolts securely.
► Fig.11: 1. Front handle 2. Hex wrench
Installing or removing drill bit
To install the drill bit, place it in the chuck as far as it will go. Tighten
the chuck by hand. Place the chuck key in each of the three holes and
tighten clockwise. Be sure to tighten all three chuck holes evenly.
To remove the drill bit, turn the chuck key counterclock-
wise in just one hole, then loosen the chuck by hand.
► Fig.12: 1. Chuck key
After use, return the chuck key to the key holder on the
tool as illustrated.
► Fig.13: 1. Key holder
Hook
CAUTION:
Always remove the battery when
hanging the tool with the hook.
CAUTION:
Never hook the tool at high loca-
tion or on potentially unstable surface.
The hook is convenient for temporarily hanging the tool.
To use the hook, simply lift up hook until it snaps into
the open position. When not in use, always lower hook
until it snaps into the closed position.
► Fig.14: 1. Hook
► Fig.15
Connecting lanyard (tether strap) to
the hook
CAUTION:
Do not use damaged hook and screws.
Before use, always check for damages, cracks or defor-
mations, and make sure that the screws are tightened.
CAUTION:
Make sure that the hook is
securely installed with the screws.
CAUTION:
Do not install or remove any
accessory while hanging the tool. The tool may fall
if the screws are not tightened.
CAUTION:
Always use a locking carabiner
(multi-action and screw gate type) and be sure to
attach the lanyard (tether strap) to the double looped
portion of the hook. Improper attachment may cause
tool drop from the hook and result in personal injury.
9 ENGLISH