Installation - IKEA FULLGÖRA Handbuch

ENGLISH
IMPORTANT: To operate properly, the function must be
on during the night and day. The function remains on until
deactivated (or it is deactivated in case of a power failure or
appliance switch-off). To deactivate the function, press the
button again. When the Eco indicator is OFF, the function is OFF.
Note: The declared appliance energy consumption refers to
operation with the Eco Night function deactivated.
F
Black Out alarm
After a power blackout, your product is designed to
automatically monitor the temperature in the freezer when
electricity is resupplied. If the temperature in the freezer rises
above freezing level, the Black Out indicator turns on, the Alarm
indicator blinks and the acoustical alarm sounds when electricity
is resupplied.
To reset the alarm press the Stop Alarm button just once.
In case of Black Out Alarm, the following actions are
recommended:
• If the food in the freezer is unfrozen but still cold, all the food
in the freezer should be eaten within the next 24 hours.
• If the food in the freezer is frozen, this indicates the food was
thawed and then refrozen when electricity was re-supplied

Installation

The appliance must be handled and installed by two or more
persons - risk of injury. Use protective gloves to unpack and install
- risk of cuts.
Installation, including water supply (if any), electrical
connections and repairs must be carried out by a qualified
technician. Do not repair or replace any part of the appliance
unless specifically stated in the user manual. Keep children away
from the installation site. After unpacking the appliance, make
sure that it has not been damaged during transport. In the
event of problems, contact the dealer or your nearest Aftersales
Service. Once installed, packaging waste (plastic, styrofoam parts
etc.) must be stored out of reach of children - risk of suffocation.
The appliance must be disconnected from the power supply
before any installation operation - risk of electric shock. During
installation, make sure the appliance does not damage the power
cable - risk of fire or electric shock. Only activate the appliance
when the installation has been completed.
Be careful not to damage the floors (e.g. parquet) when
moving the appliance. Install the appliance on a floor or support
strong enough to take its weight and in a place suitable for
its size and use. Make sure the appliance is not near a heat
When contacting our Service Provider, please state the codes
provided on your product's identification plate.
The model information can be retrieved using the QR-Code
reported in the energy label. The label also includes the model
identifier that can be used to consult the
https://eprel.ec.europa.eu database portal.
*On the rating plate the article number is 8 digits
Inspection check list
Please follow the inspection checklist before using your appliance.
If any answer is NOT please follow the relevant action.
Please remember to write down the product serial number and
article number as required and attach your receipt to this page.
Product serial number (rating plate) *
Product artical number (rating plate) **
Purchasing date
which degrades taste, quality and nutritional value and also
could be unsafe. It is recommended to not consume the food
but to dispose of the entire content of the freezer. The Black
Out Alarm is designed to provide guidance on food quality in
the freezer in the event of electricity black out. This system does
not guarantee food quality or safety and consumers are advised
to use their own judgment in evaluating food quality in freezer
compartment.
Turning Off the sound alarm
To mute the alarm buzzer press Stop Alarm button just once
To avoid food waste, please refer to the recommended To avoid
food waste, please refer to the recommended setting and
storage times found in the user manual.
source and that the four feet are stable and resting on the floor,
adjusting them as required, and check that the appliance is
perfectly level using a spirit level. Wait at least two hours before
switching the appliance on, to ensure that the refrigerant circuit is
fully efficient.
WARNING: When positioning the appliance, ensure the
supply cord is not trapped or damaged.
WARNING: To avoid a hazard due to instability, positioning
or fixing of the appliance must be done in accordance with the
manufacturer instructions. It's forbidden to place the refrigerator
in such way that the metal hose of gas stove, metal gas or water
pipes, or electrical wires are in contact with the refrigerator back
wall (condenser coil).
To guarantee adequate ventilation, leave a space on both
sides and above the appliance. The distance between the rear
of the appliance and the wall behind the appliance should be 50
mm, to avoid access to hot surfaces. A reduction of this space
will increase the Energy consumption of product. Please remove
the power cord from condenser hook during installation before
connecting product to power supply.
XXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX XXXXXXXXX XXXXXXXXXXXXX
XXXXXXXXXXXXX XXXXXXXXXXXXX
XXXXX XXXXX XXXXX XXXXX
XXXXX XXXXX XXXXX XXXXX
XXXXX XXXXX XXXXX XXXXX
G
XXXXXXXXX
XXXXXXXXX
XXXXXXXXX
XXXXXXXXXXXXX
XXXXX
XXXXX
XXXXX
**On the rating plate the
serial number is 12 digits
7