Operation - EINHELL BT-RO 1200-12 Originalbetriebsanleitung

Anleitung_BT_RO_1200_12_SPK7:_
GB
5.2 Parallel stop assembly (Fig. 3/Item 21)
Push the guide shafts (a) of the parallel stop (21)
into the holes (b) on the routing shoe (2).
Set the parallel stop (21) to the required
dimension and secure it in place with the wing
screws (3).
5.3 Fitting the compass point (Fig. 4)
You can route circular areas using the compass
point (13) and the mounting to go with it.
Clamp the compass point (13) to the end of one of
the guide rods (a). Push the guide rod (a) into a
hole (b) on the routing shoe (2). Secure the guide
rod (a) on the routing shoe (2) using the securing
screws (8).
Set the required radius between the compass point
(13) and cutter.
Position the compass point (13) in the center of the
circle you wish to route. If necessary undo the wing
screw (c) on the compass point (13) and
extend/shorten the part of the compass point (13)
that points downwards.
5.4 Guide sleeve assembly (Fig. 5-6/Item 20)
Secure the guide sleeve (20) to the routing shoe
(2) using the two countersunk screws (f).
The guide sleeve (20) is guided along the
template (c) using the guide ring (b).
The workpiece (d) must be larger by the
difference of "external edge of guide ring" and
"external edge of router" (e) to obtain a precise
copy.
5.5 Fitting / Removing the cutting tool (Fig. 7-10)
Important. Pull out the power plug first.
Important. After working with the router, the
cutting tool will remain very hot for a relatively
long time.
Important. Cutters are very sharp. Wear
protective gloves at all times when handling
cutting tools.
Cutters with a shaft diameter of 12 mm can be
fitted to this router. .
You can used cutters made of the following
materials:
- HSS – Suitable for machining softwood
- TCT – Suitable for machining hardwood,
particle board, plastic and aluminum.
Select the appropriate cutting tool for the job in
hand.
When using the cutters for the first time:
Remove the plastic packaging from the cutter
heads.
Clean the nut, clamp and shaft of the cutter
16
04.04.2012 14:06 Uhr
before fitting it.
Press the spindle lock (12) and allow the spindle
to engage by turning it at the same time.
Undo the clamp nut (10) using the open-ended
spanner (22).
If necessary take the cutter you wish to remove
out of the clamp (a).
Select the appropriate cutting tool for the job in
hand.
Now fit the clamp (a) and nut (10) into the cutting
spindle.
Guide the cutter shaft into the clamp.
Press and hold the spindle lock (12).
Tighten the clamp nut (10) using the open-ended
spanner (22).
The cutter must be inserted at least 20 mm into
the clamp (a).
Before you start the electric router, check to
ensure that the cutting tool is secure and runs
smoothly.

6. Operation

Never use a low-quality or damaged routing
cutter. Use only cutting tools with a shaft
diameter of 12 mm. The cutters must also be
designed for the respective idling speed..
Secure the workpiece so that it cannot be thrown
through the air as you work on it. Use clamps or
a vise.
Always guide the power cable away from the
back of the tool.
Never cut over metal parts, screws, nails etc.
6.1 ON/OFF switch (Fig. 11/Item 4)
Press the safety lock-off (5) and then press the
ON/OFF switch (4) to switch on the machine.
Release the ON/OFF switch (4) to switch off the
machine.
6.2 Speed control (Fig. 12 – Item 11)
The best speed depends on the material and the
diameter of the cutter. Select a speed between
16,000 and 30,000 rpm using the speed control
switch (11). You can choose from 6 different switch
positions. The speeds in the various switch positions
are as follows:
Switch position 1: approx. 16,000 rpm (minimum
speed)
Switch position 2: approx. 18,000 rpm
Switch position 3: approx. 21,000 rpm
Switch position 4: approx. 24,000 rpm
Switch position 5: approx. 27,000 rpm
Switch position 6: approx. 30,000 rpm
Seite 16