Operation; Maintenance - Makita DUR366L Betriebsanleitung

Never use the tool without the guard illustrated
in place. Failure to do so can cause serious
•
personal injury.
CAUTION:
•
Take care not to injure yourself on the cutter
for cutting the nylon cord. (Fig. 13)
Align the clamp on the pipe with the protector. And
tighten them with bolts.
Installing nylon cutting head or plastic
blade (optional accessory)
CAUTION:
• If the nylon cutting head/plastic blade accidentally
impacts a rock or hard object during operation,
stop the tool and inspect for any damage. If the
nylon cutting head/plastic blade is damaged,
replace it immediately. Use of a damaged cutting
tool could result in serious personal injury.
NOTICE:
• Be sure to use genuine Makita nylon cutting head/
plastic blade.
Turn the tool upside down so that you can replace the
nylon cutting head easily.
Insert the hex wrench through the hole on the motor
housing and rotate the receive washer until it is locked
with the hex wrench. Place the nylon cutting head/plastic
blade onto the threaded spindle directly and tighten it by
turning it counterclockwise. Remove the hex wrench.
(Fig. 14 & 15)
To remove the nylon cutting head/plastic blade, turn it
clockwise while holding the receive washer with the hex
wrench.
Hex wrench storage (Fig. 16)
When not in use, store the hex wrench as shown in the
figure to keep it from being lost.

OPERATION

Correct handling of tool
Correct posture (Fig. 17)
WARNING:
• Always position the tool on your right-hand side.
Correct positioning of the tool allows for maximum
control and will reduce the risk of serious personal
injury caused by kickback.
• Be extremely careful to maintain control of the tool
at all times. Do not allow the tool to be deflected
toward you or anyone in the work vicinity. Failure
to keep control of the tool could result in serious injury
to the bystander and the operator.

MAINTENANCE

WARNING:
• Always be sure that the tool is switched off and
battery cartridge is removed before attempting to
perform inspection or maintenance on the tool.
Failure to switch off and remove the battery cartridge
may result in serious personal injury from accidental
start-up.
NOTICE:
Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Replacing the nylon cord
WARNING:
• Never use metal wire, rope or the like. Use
recommended nylon cord only, otherwise it may cause
damage to the tool and result in serious personal
injury.
• Make sure that the cover of the nylon cutting head
is secured to the housing properly as described
below. Failure to properly secure the cover may
cause the nylon cutting head to fly apart resulting in
serious personal injury.
Take off cover from housing, pressing two latches which
are slotted section oppositely on side of housing. (Fig.
18) Cut a nylon line in 3 m. Fold the cutting line in two
halves, leave one of half longer 80-100 mm than another.
(Fig. 19)
Hook the middle of the new nylon cord to the notch
located at the center of the spool between the 2 channels
provided for the nylon cord.
Wind both ends firmly around the spool in the direction
marked on the head for left hand direction indicated by
LH. (Fig. 20)
Wind all but about 100 mm of the cords, leaving the ends
temporarily hooked through a notch on the side of the
spool. (Fig. 21)
Mount the spool on the cover so that the grooves and
protrusions on the spool match up with those on the cover.
Now, unhook the ends of the cord from their temporary
position and feed the cords through the eyelets to come
out of the cover. (Fig. 22)
Align the protrusion on the underside of the cover with
the slots of the eyelets. Then push the cover firmly onto
the housing to secure it. Make sure the latches fully
spread in the cover. (Fig. 23)
Replacing the blade for plastic blade (Fig.
24)
Replace the blade when it is worn out or broken.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
17