Edited Recording On Sides A And B Of A Tape; Auto On Function - Denon UD-M31 Bedienungsanleitung

(8) Playing the tracks in random order ........................................................................
(Using the remote control unit)
• Use this function to play all the tracks on the disc once
in random order.
• In the normal playback mode, simply press the
RANDOM button to set random playback.
• If the RANDOM button is pressed while the repeat
mode is set, the tracks are each played once in
random order, then played again in another order,
and so on.
• The repeat mode is set to the all-track repeat mode
when the RANDOM button is pressed during single-
track repeat mode.
NOTES:
• The total remaining time cannot be displayed during the random playback mode.
• The random playback mode cannot be set during editing.

Edited Recording on Sides A and B of a Tape

This function allows edited recording according to the length of the tape. (This operation is only possible from the
remote control unit.)
Edited recording is a system function of the D-M31 series. This function can only be used in combination with the DRR-
M31.
• Use this function to efficiently edit the tracks on a CD according to the length (time) of the tape onto which you want
to record.
NOTES:
• Load a blank cassette tape onto which you want to record in the cassette deck with side A on the top before
starting the editing procedure. The tape is automatically wound to the beginning before recording starts.
• The editing mode is canceled when the CD receiver's stop button is pressed.
• Note that even if the tape is slightly longer than the disc's total playing time, it may not be possible to record all
the tracks on sides A and B because of the combination of tracks to be recorded on the different sides of the tape.
• When recording on an already recorded tape, if the tape is longer than the new recording, the previous recording
will remain at the end of side B, so erase the tape before starting.
• During edited recording, only the stop button, power operation switch, and TIME button for the CD player section
and the stop button and power operation switch for the cassette deck will function.
• Set the reverse mode on the cassette deck (DRR-M31) to
• Edited recording does not function when you play a disc with more than 26 tracks.
(1) Recording the tracks in the same order as on the disc................................................
2, 3
CD RECEIVER UD-M31
MENU / SET
TONE/SDB
FUNCTION
ON / STANDBY
PHONES
1
Random Playback
SYSTEM
TITLE/CHARACTER TIME POWER
EDIT
RANDOM SLEEP
RANDOM button
TUNING TUNING
RDS
ENTER
MEMORY
REPEAT FUNCTION
TONE /SDB
TUNER
PTY PRESET
- +
PROG /
DIRECT BAND
CD-R MD
GROUP
CT
VOLUME
DISC
SKIP
CD
1 2 3
CALL DISPLAY
or during edited recording.
Automatic Edited Recording
SYSTEM
TITLE/CHARACTER TIME POWER
5
4
EDIT
RANDOM SLEEP
TUNING TUNING
RDS
ENTER
MEMORY
BAND
REPEAT FUNCTION
TONE /SDB
1
TUNER
PTY PRESET
- +
+
-
PROG /
DIRECT
BAND
VOLUME
GROUP CD-R MD
CT
VOLUME
5
DISC
SKIP
CD
1 2 3
CALL DISPLAY
4 5 6
4
PANEL
7 8 9
CLEAR
10 +10
Example: Recording a disc containing 16 tracks and a total playing time of 56 minutes on a C-60 cassette tape
1
Press the FUNCTION button to set the CD mode.
Press the (open/close) button to open the disc
5
2
tray.
• Load the disc in the disc tray.
Press the 5 (open/close) button to close the disc
3
tray.
• The display appears after several seconds.
Press the EDIT button on the remote control unit to
set the length of the tape. (The length is the total for
sides A and B.)
• For a 60-minute (C-60) tape, press the EDIT button
2 times.
• The display changes as shown below each time
the EDIT button is pressed.
(If the tape length has already been set once, the
display changes starting from that length.)
4
C-46 C-60 C-90 C---
(Cancelling the editing mode)
Inputting other tape sizes:
• To input other tape sizes, use the number and
+10 buttons when "C ---" is displayed.
After this, the remaining times for sides A and B are
displayed alternately for several seconds
Press the / (play/pause) button.
1 3
5
• The tape is automatically wound to the beginning
on the cassette deck, then recording starts.
• To set a time other than 46, 60 or 90, input the time when "C —" is displayed. The time can be set to up to 99
minutes input in the same way as when inputting track numbers for the CD direct search operation.
13

AUTO ON FUNCTION

• When the / (play /pause) button or (open/close) button on the CD receiver is pressed while the power is set to
1 3 5
STANDBY mode, the power automatically turns on and the play or open/close operation is performed.
• When the CD 1 / 3 , TAPE 1 , TAPE 0 , or MD 1 / 3
set to STANDBY mode, the power automatically turns on and the play operation is performed.
• In the same way, when the tuner TUNER buttons on the remote control unit is pressed, the power turns on and the
corresponding station is tuned in.
FUNCTION
Example: For a 60-minute tape
EDIT
Side A display - Tracks 1 to 9 will be
recorded on side A.
2 minutes 40 seconds remaining on
side A
Side B display - Tracks 10 to 16 will be
recorded on side B.
1 minute, 20 seconds remaining on
side B
Track no. Elapsed time
button on the remote control unit is pressed while the power is
ENGLISH
21