Wall Assembly; Power Switch - Honeywell SH-771E Gebrauchsanweisung

Cord Storage
1. This quick heater is equipped with Cord
Storage (16). To securely store the Supply
Cord (15), fully put it into the Storage (16)
by pressing it through the hole.
2. Before operating the quick heater make
sure that the Supply Cord (15) is fully
pulled out and extended.

Wall Assembly

If you would like to wall-mount the quick heater,
follow these instructions:
1. Slightly press a screwdriver onto the
marking of the Wall-Mounting Support (2)
and take the Support (2) off the quick
heater.
2. Make sure that the minimum Safety
Distances (4) to walls, floors and ceilings
are kept.
3. Drill holes of Ø 6 mm in the wall, using the
Support (2) as an assembly stencil.
4. Insert plugs of Ø 6 mm into the holes and
fix the Wall-Mounting Support (2) with two
screws of Ø 5 mm.
5. Suspend the Opening for the Wall-
Mounting Support (1) onto the Support (2),
until you hear a "click". The quick heater is
now securely installed.
6. Choose the desired air flow position within
the variable air flow range (5) by turning
the quick heater into the desired position.
7. If you want to take the quick heater off the
Wall-Mounting Support (2), make sure it is
centered. Then follow instructions
under 1.
Operating Instructions
SH-771E Quick Heater with Thermostat Switch
SH-772E Quick Heater with Power and
Thermostat Switch
SH-773E Quick Heater with Power and
Thermostat Switch, Pilot Light and
Wall-Mounting Support
1. Check that the Power Switch (7) is in
off-position (10). Plug the Supply Cord (15)
into the outlet. Do not touch the Supply
Cord (15) with wet hands.
2. Check that the Air Inlet (14) and Outlet (6)
are not covered. The Air Inlet (14) and
Outlet (6) must not be covered during
operation.
ENGLISH
3. To operate the quick heater by use of the
Power Switch (7) and/or Thermostat Switch
(9) follow the below instructions.
4. Before removing or moving the quick
heater turn the Power Switch (7) to the off-
position (10) and disconnect it from the
electricity supply.

Power Switch

1. Turn the Power Switch (7) clockwise to one
of the four settings:
Off (10)
Warm Air 1000 W
„Whisper-quiet operation" (11)
Warm Air 1200 W (12)
Hot Air 2000 W (13)
When the Power Switch (7) is in the Hot
2.
Air 2000W (13) position it cannot be
turned further clockwise, only
counter-clockwise.
Thermostat Switch
1. If equipped with a Power Switch (7) make
sure that it is turned to one of the heat
settings.
2. Turn the Thermostat Switch (9) clockwise to
the highest setting 8 (18).
3. When the desired room temperature is
reached, turn the Thermostat Switch (9)
counter-clockwise until you hear a "click".
The quick heater stops operating.
4. Now turn the Thermostat Switch (9) a little
clockwise again. The quick heater will
maintain the selected room temperature by
automatically switching the quick heater on
and off.
5. The further you turn the Thermostat Switch
(9) clockwise, the higher the heating
temperature. The highest setting 8 (18)
corresponds to a room temperature of
approx. 30 °C, the lowest setting
(17) to approx. 5 °C.
6. It is normal that the Thermostat will not
operate the quick heater when the room
temperature is above 30 °C.
7. When the room temperature is below 5 °C
the quick heater will operate until the room
temperature is above 5 °C.
8. When the Thermostat Switch is in position
8 (18) it cannot be turned further
clockwise, only counter-clockwise.
5