Additional Safety Instructions; Noise And Vibration - Flex L 1506 VR Originalbetriebsanleitung

 Keep your body out of the area into which
the electric power tool moves when
a recoil occurs. Kickback propels the
electric power tool in the direction
opposite to the movement of the sanding
disc at the point of pinching.
 Work especially carefully near corners,
sharp edges, etc. Prevent the insertion
tool from recoiling off the workpiece and
jamming.
The rotating insertion tool has a tendency
to snag on corners, sharp edges or if it
bounces. This causes a loss of control or
kickback.
 Do not use a chain or toothed saw blade.
Such insertion tools frequently cause
a kickback or the loss of control of the
electric power tool.
Special safety instructions
for sanding:
 Do not use oversized sanding sheets, but
follow the manufacturer's specifications
for the size of sanding sheets. Sanding
sheets which project over the sanding pad
may cause injuries as well as block and rip
the sanding sheets or cause a kickback.

Additional safety instructions:

 The mains voltage and the voltage
specifications on the rating plate
must correspond.
 Do not press the spindle lock until
the tool stops.

Noise and vibration

The noise and vibration values have been
determined in accordance with EN 60745.
The A evaluated noise level of the power tool
is typically:
L 1506 VR
LG 1704 VR
18
Downloaded from www.Manualslib.com
Sound Sound
pressure power
L [dB(A)] L [dB(A)]
pA WA
86 97
87 98
Uncertainty K = 3 dB
manuals search engine
L 1506 VR, LG 1704 VR
Total vibration value (when grinding surfaces):
Emission value a
L 1506 VR
LG 1704 VR
Uncertainty K = 1.5 m/s
Total vibration value (when grinding with
sanding sheet):
Emission value a
L 1506 VR
LG 1704 VR
Uncertainty K = 1.5 m/s
t^okfkd>
qÜÉ=áåÇáÅ~íÉÇ=ãÉ~ëìêÉãÉåíë=êÉÑÉê=íç=åÉï=
éçïÉê=íççäëK=a~áäó=ìëÉ=Å~ìëÉë=íÜÉ=åçáëÉ=~åÇ=
îáÄê~íáçå=î~äìÉë=íç=ÅÜ~åÖÉK
klqb
The vibration emission level given in this
information sheet has been measured in
accordance with a standardised test given in
EN 60745 and may be used to compare one
tool with another. It may be used for a preliminary
assessment of exposure. The declared vibration
emission level represents the main applications
of the tool.
However if the tool is used for different
applications, with different accessories or poorly
maintained, the vibration emission may differ.
This may significantly increase the exposure level
over the total working period. For a precise
estimation of the vibration load the times should
also be considered during which the power tool
is switched off or even running, but not actually
in use.
This may significantly increase the exposure level
over the total working period Identify additional
safety measures to protect the operator from the
effects of vibration such as: maintain the tool and
the accessories, keep the hands warm,
organisation of work patterns.
`^rqflk>
tÉ~ê=É~ê=éêçíÉÅíáçå=~í=~=ëçìåÇ=éêÉëëìêÉ=
~ÄçîÉ=UR=Ç_E^FK
2
[m/s ]
h
5.4
–
2
2
[m/s ]
h
3.8
2.2
2