5.32 Sweep Menu - Hameg HM 8131-2 Handbuch

Steps necessary to ensure synchronization
of master and slaves:
Master
1. Definition of master und slave(s)
*** MAIN Menu 1 ***
Sweep Arb Mode -->
** WORKING MODE **
Cnt Trg Gat Sync
** MULTI-DEV SYNC **
Master Pulse Slave
2. Connect all terminals[19] 10MHz IN/OUT
of master and slaves
3. Set reference frequency at terminal[19]
*** MAIN Menu 2 ***
Mod Phi Option <--
** OPTIONS MENU 3 **
<-- Ref Disp -->
FREQUENCY REFERENCE
Int Ext
Internal reference fre-
quency programmed as output
from terminal[19] 10MHz
IN/OUT
4. Connect TrigOut[18] of master to TrigIn[2]
of slave(s)
5. Set desired phase on slaved generators
6. Generate a trigger pulse from the master in
order to synchronize all. This can be a trigger
pulse into terminal TrigIn[2], of the master
or a pulse generated by pushing button Pulse
or a trigger pulse via an interface.
*** MAIN Menu 1 ***
Sweep Arb Mode -->
** WORKING MODE **
Cnt Trg Gat Sync
** MULTI-DEV SYNC **
Master Pulse Slave
Subject to change without notice
Downloaded from www.Manualslib.com
*** MAIN Menu 1 ***
Sweep Arb Mode -->
** WORKING MODE **
Cnt Trg Gat Sync
** MULTI-DEV SYNC **
Master Pulse
*** MAIN Menu 2 ***
Mod Phi Option <--
** OPTIONS MENU 3 **
<-- Ref Disp -->
FREQUENCY REFERENCE
out:on Int Ext
External reference fre-
quency programmed as
input to terminal[19]
10MHz IN/OUT als Input
10 MHz-Referenz
*** MAIN Menu 2 ***
Mod Phi Option <--
Phase : 120.0 deg
- val + < cur >
manuals search engine
As soon as the master receives a trigger signal it will forward this
signal to the slave(s). With synchronisation established all
generators will operate in phase-lock. Of course, if the signal
frequency is to be changed synchronization will have to be
Slave
renewed.
Please note that all adjustments for synchronization
will not be stored, so, after switching off, they will
be lost. The internal oscillator of the master determines the
frequency stability of all the generators.
STOP
In sync master and slave(s) are phase-locked. After the
Slave
master was triggered it takes some time for the slaves
to react and get started, hence there will be a time delay
depending on the frequency and the propagation time
of the trigger signal resulting in a fixed delay between
STOP
the output signals of the master and those of the slaves.
At high frequencies there will also be a delay between
the individual slaves. In the MAIN MENU 2 there is
provision to correct for such delays going to (Phi). The
following tables summarizes approximate values for
the phase difference:
TiPP
Signal
frequency
10 kHz
100 kHz
1 MHz
10 MHz

5.32 Sweep menu

Look for all necessary parameters in the menu "SWEEP PARA-
METERS". The sweep mode complements the standard operating
modes of the HM 8131-2. The mode, however, allows only free
running or triggered operation.
The sweep mode does not allow gated operation.
Sweep Menu HM8131-2
STOP
* SWEEP PARAMETERS *
Start Stop Time Lin
Main menu 1 and functions
Delta phase Delta phase
master/slave slave/slave
appr. 0 appr. 0
appr. 8 degr. appr. 0
appr. 40 degr. appr. 3 degr.
appr. 160 degr. appr. 20 degr.
Lin: "Select linear or
logarithmic"
SweepTime: 1.00 sec
- val + < cur >
Sp: 1.0000000 MHz
- val + < cur >
St: 100.0000 kHz
- val + < cur >
63