Safety Devices; Auto-Stop Function; Symbols On The Device; Assembly - Kärcher K 5 Premium Smart Control Originalbetriebsanleitung

Trigger "0/OFF" / "I/ON"
6
Storage for spray lance
7
High-pressure hose
8
*Plug 'n' Clean detergent bottle
9
Storage / parking position for high-pressure gun
10
3-in-1 multi-jet spray lance with 3 spray types (see
11
also chapter Smart Control System)
Smart Control high-pressure gun
12
LCD display (see also chapter LCD display)
13
Battery compartment lock
14
Battery compartment
15
"+/-" buttons for pressure control
16
High-pressure gun lock
17
Button for separating the high-pressure hose from
18
the high-pressure gun
High-pressure gun lever
19
Transport handle, telescoping
20
Carrying handle
21
Hose holder
22
High pressure hose reel
23
Crank handle for hose reel
24
Type plate
25
Accessory compartment
26
Hook for net attachment
27
Accessory compartment net
28
Mains connection with mains plug
29
Supplied screws and dowels
30
Water connection coupling
31
**Garden hose with commonly available coupling
32
– Fabric reinforced
– Diameter of at least 1/2 inch (13 mm)
– Length at least 7.5 m
**KÄRCHER suction hose for water supply from
33
open containers (order no. 2.643-100.0)
*Foam nozzle with detergent container
34
The detergent is sucked out of the container to pro-
duce a strong detergent foam.
*Rotating washing brush (e.g. for washing cars)
35
* optional, ** additionally required
LCD display
Illustration C
Area of application (1-SOFT / 2-MEDIUM / 3-HARD
1
with 2 pressure levels each)
BOOST function indicator
2
Spray type recommendation (flat stream/detergent/
3
dirt grinder)
®
Display Bluetooth connection
4
Signal strength status (four levels)
5
Battery status (empty, almost empty, medium, full)
6
Detergent level (1 / 2 / 3)
7
Supplied screws and dowels
Illustration D
Stand dowels (2 pieces)
1
Screw M 4x20 (2 pieces)
2
Screw M 4x22 (2 pieces)
3
Screw M 4x16 (8 pieces)
4

Safety devices

CAUTION
Missing or modified safety devices
Safety devices are provided for your own protection.
Never modify or bypass safety devices.
The power switch prevents unintentional operation of
the device.
High-pressure gun lock
The lock locks the lever of the high-pressure gun and
prevents the device from starting unintentionally.

Auto-stop function

If the lever of the high-pressure gun is released, the
pressure switch turns off the pump and the high-pres-
sure jet stops. The pump switches on again when the le-
ver is pressed.
Motor circuit breaker
The motor circuit breaker shuts off the device if power
consumption it too high.

Symbols on the device

Do not aim the high-pressure jet may at per-
sons, animals, live electrical equipment or
the device itself.
Protect the device against frost.
The device may not be connected to the
public drinking water network.
For the illustrations, refer to the graphics page.
Place the screws provided and matching screwdriver at
the ready.
Fit the supplied loose parts onto the device before start-
ing up the device.
Fitting the wheels
1. Insert the wheels.
Note
Pay attention to the alignment of the hole.
Illustration E
2. Secure the wheels with 1 screw each.
Mounting the stand
1. Insert the stand.
Illustration F
2. Insert the 2 dowels into the holes as far as they will
go.
3. Secure the base with 2 screws.
Installing the spray lance storage
1. Hang the spray lance storage in position.
2. Secure the storage with 2 screws.
Illustration G
3. Secure the cover with 4 screws.
Illustration H
English
Power switch

Assembly

15