Noise Development; Technical Data - Clatronic km 2717 Bedienungsanleitung

6. Position the cover of the mixer drive (19) on the base of the
machine so that the ▼ arrow is pointing to the circular
mark on the base. Then turn the mixer (3) or the mixer drive
cover (19) clockwise until the ▼ arrow is pointing to the
mark on the base of the machine.
Double Safety System: The motor can only be switched on
if the bowl is correctly locked in place with the lid and at the
same time the mixing vessel or the cover for the mixer drive (19)
is correctly mounted. Only remove the lid of the bowl and the
mixing vessel when the machine is switched off.
Mixer function
• The bowl must be fi xed in place as described under section
1 and 5 (without utensil).
• Chop the food to be mixed into small pieces.
• Fill the mixer vessel (3) with the food to be mixed (max.
1.5 l). Never fi ll with hot food or hard ingredients such as
potatoes, ice, coffee beans, nuts, and so on.
• Position the lid (4) with the pouring aperture facing to the
right and then lock this in place by turning it anticlockwise.
• Close the fi lling slot seal (5).
• Mount the mixing bowl (3) as described in paragraph 6.
• Extra ingredients (e.g. seasoning) can also be added
through fi lling slot in the mixer lid. Switch off the appliance.
Mixing bowl
• The lid of the mixing device (19) must be mounted as
described in paragraph 6.
• The mixing bowl must be mounted as described in para-
graph 1.
• Press the metal knife (15) or the plastic knife (16) down-
wards as far as possible without the utensil holder.
• When grating/cutting attachments are used, place the
desired utensil on to the utensil holder (14).
• Never use more than one utensil at a time.
• Position the lid of the bowl (8) as described under points 4
and 5.
• Use the fi ller (17) to press the food (max. 1.5 l) into the
fi lling slot. Exert a suffi cient degree of pressure on the fi ller.
The appliance must be switched on only with the fi ller (17)
mounted into place.
Putting into function
• Connect the appliance to a 230 V/50Hz socket.
• Interval switching (P): turn the appliance switch to the left
at brief and regular intervals several times. By doing so, the
result of the operation can be checked gradually.
26
05-KM 2717 N4 26
Always choose a utensil and a speed according to the following
table:
Product/ Max.
Utensil
Type of Preparation Quantity
Heavy dough
500 g plastic knife
(e.g. yeast dough)
Cake mixture 750 g plastic knife
Sponge mixture or
750 g plastic knife
wafer mixture
Cutting up, e.g. fruit,
500 g metal knife
vegetables, meat
Cutting cucumbers, cutting
500 g
carrots attachment 12
Grating carrots, radish,
500 g fi ne grater
cheese
Grating apples and
500 g coarse grater
carrots
Grating potatoes,
500 g grating attachment II to III
hard cheese
Potatoes 500 g chip disk
Liquids, shakes up to 1.5 l mixing vessel
Note: The cutting and grinding attachments are located in the
accessory drawer (20) under the machine.
Cleaning
• Remove the plug from the socket before cleaning!
• Clean the bowl and the mixing vessel carefully immediately
after each procedure. To do so, remove the bowl in order to
be able to clean off any residues on the drive shaft.
• Never use sharp objects for cleaning!
• Never use abrasive detergents!
• Use a moist towel to clean the outside of the basis appliance.
• In the case of intensely colored foodstuffs (e.g. carrots), the
plastic parts can be stained: clean them with oil.
• Any removable parts which have come into contact with
food (utensil and bowls) can be cleaned in soapy water.

Noise development

The sound pressure level in the ear of an operator (LpA) was
measured according to DIN EN ISO 3744.
Sound pressure level detected: 84.1 dB(A) (no limit)

Technical Data

Model: ..............................................................................KM 2717
Power supply:............................................................230 V, 50 Hz
Power consumption :........................................................... 700 W
Protection class:.......................................................................... ΙΙ
This device has been tested according to all relevant current
CE guidelines, such as electromagnetic compatibility and low
voltage directives, and has been constructed in accordance with
the latest safety regulations.
Subject to technical changes without prior notice!
Max.
Level Operating
Time
I to II 3 min
II to III 5 min
II to III 5 min
II to III 5 min
II to III 5 min
II to III 5 min
II to III 5 min
5 min
II to III 3 min
III or P 2 min
02.05.2006, 11:58:04 Uhr