Operation - EINHELL TE-TS 36/210 Li-Solo Originalbetriebsanleitung

6.7.2 Dust extraction using a vacuum ext-
raction system and extractor adapter set
(Fig. 12)
•
The product is not supplied with an extractor
adapter set with suction hose (a) and adapter
(b) or a vacuum extraction system, which are
available as accessories.
•
Using a crosstip screwdriver, undo the screw
on the cap (38) on the saw blade guard (2).
•
Remove the cap (38) from the saw blade gu-
ard (2).
•
Connect the adapter (b) to the extractor ad-
apter on the housing (16).
•
Connect the saw blade guard (2) and the ad-
apter (b) to the suction hose (a).
•
A vacuum extraction system can now be con-
nected to the 100 mm diameter of the adapter
(b).

7. Operation

7.1 ON/OFF switch (Fig. 1, 13)
•
Flip the switch (11) up to switch on the saw.
Wait for the blade to reach its maximum
speed of rotation before commencing with the
cut.
•
To switch off the saw again, the switch (11)
has to be flipped down.
7.2 Cutting depth (Fig. 1, 14)
Turn the hand wheel (8) to set the blade (4) to the
required cutting depth.
Turn anti-clockwise:
smaller cutting depth
Turn clockwise:
larger cutting depth
7.3 Parallel stop
The parallel stop (7) has to be used when making
longitudinal cuts in wooden workpieces.
7.3.1 Stop height (Fig. 1c, 15)
•
The parallel stop (7) which is supplied with
the product must be used together with the
stop rail (23) when performing longitudinal
cuts on thin materials (see Fig. 15a).
•
To fasten the stop rail (23) to the parallel
stop (7) you have to slacken the two knurled
screws (26). Then thread the stop rail (23)
with the slot (25) onto the lock bolts (28) and
secure it with the washers (27) and knurled
screws (26).
Anl_TE_TS 36_210_Li_Solo_SPK9.indb 31 Anl_TE_TS 36_210_Li_Solo_SPK9.indb 31
GB
•
The parallel stop (7) has to be used without
the stop rail (23) when making longitudinal
cuts in thicker wooden workpieces (see Fig.
15b). To do this, the lock bolts (28), washers
(27) and the knurled screws (26) must also be
removed.
•
Warning! When in use, the stop rail (23) must
always be screwed to the side of the parallel
stop (7) which faces the saw blade.
7.3.2 Cutting width (Fig. 16)
•
The parallel stop (7) can be mounted on eit-
her side of the saw table (1).
•
The parallel stop (7) has to be mounted in the
guide rail (29) of the saw table (1).
•
You can clamp the parallel stop (7) in the re-
quired position by pressing the eccentric lever
(12).
When the table width extension (10) is ret-
racted and/or for cutting widths of less than
25 cm:
•
Using the main scale (22) on the guide rail
(29), adjust the parallel stop (7) to the requi-
red dimension.
When the table width extension (10) is exten-
ded and/or for cutting widths of more than
25 cm:
•
Using the main scale (22), adjust the parallel
stop (7) to the 25 cm angle and secure it with
the eccentric lever (12).
•
To then increase the cutting width, adjust the
rest of the cutting width by pulling out the tab-
le width extension (10) (see 7.6).
•
Read off the total cutting width setting which
has been set on the additional scale (24). Im-
portant! To ensure that the cutting dimension
on the additional scale (24) is correct, the
parallel stop (7) must be set to the defined
dimension of 25 cm on the main scale (22).
7.3.3 Setting the stop length (Fig. 17)
•
The stop rail (23) can be moved in longitudi-
nal direction in order to prevent the workpiece
from becoming jammed.
•
Rule of thumb: The rear end of the stop co-
mes up against an imaginary line that begins
roughly at the center of the blade and runs at
an angle of 45° to the rear.
•
Set the required cutting width
- Slacken the knurled screws (26) and push
the stop rail (23) forward until it touches the
imaginary 45° line.
- Retighten the knurled screws (26).
- 31 -
19.03.2020 13:23:44 19.03.2020 13:23:44