Use And Maintenance - Indesit H 361 Gebrauchsanweisung

Use and maintenance

version prepare the hole for evacuation of the air.
• We recommend the use of an air exhaust tube which
has the same diameter as the air exhaust outlet hole. If a
pipe with a smaller diameter is used, the effi ciency of the
product may be reduced and its operation may become
noisier.
• Fixing to the wall
Drill the holes A1 respecting the distances indicated
(Fig.2). Fix the appliance to the wall and align it in
horizontal position to the wall units.
When the appliance has been adjusted, defi nitely fi x the
hood using the screws A2 (Fig.5).
For the various installations use screws and screw
anchors suited to the type of wall (e.g. reinforced concrete,
plasterboard, etc.). If the screws and screw anchors are
provided with the product, check that they are suitable for
the type of wall on which the hood is to be fi xed.
• Fixing the decorative telescopic fl ue
Take care not to scratch the duct; wear gloves when
removing the protective fi lm. (Fig. 3).
Arrange the electrical power supply within the dimensions
of the decorative fl ue. If your appliance is to be installed in
the ducting version or in the version with external motor,
prepare the air exhaust opening.
Adjust the width of the support bracket of the upper fl ue
(Fig.4). Then fi x it to the ceiling using the screws A (Fig.4)
in such a way that it is in line with your hood and respecting
the distance from the ceiling indicated in Fig.2.
Connect the fl ange C to the air exhaust hole using a
connection pipe (Fig.5).
Insert the upper fl ue into the lower fl ue and rest above
the frame. Extract the upper fl ue up to the bracket and fi x
it with the screws B (Fig.4).
To transform the hood from a ducting version into a fi ltering
version, ask your dealer for the charcoal fi lters and follow
the installation instructions.
• Filtering version
Install the hood and the two fl ues as described in the
paragraph for installation of the hood in ducting version.
To assemble the fi ltering fl ue refer to the instructions
contained in the kit. If the kit is not provided, order it from
your dealer as accessory.
The fi lters must be applied to the suction unit positioned
inside the hood. They must be centred by turning them 90
degrees until the stop catch is tripped (fi g. 8).
Use and maintenance
• We recommend that the cooker hood is switched on
before any food is cooked. We also recommend that the
appliance is left running for 15 minutes after the food is
cooked, in order to thoroughly eliminate all contaminated
air.
The effective performance of the cooker hood depends on
constant maintenance; the anti-grease fi lter and the active
carbon fi lter both require special attention.
• The anti-grease fi lter is used to trap any grease particles
suspended in the air, therefore is subject to saturation (the
time it takes for the fi lter to become saturated depends on
the way in which the appliance is used).
- To prevent potential fi re hazards, the anti-grease fi lters
should be washed a minimum of every 2 months (it is
possible to use the dishwasher for this task).
- After a few washes, the colour of the fi lters may change.
This does not mean they have to be replaced.
If the replacement and washing instructions are not
followed, the anti-grease filters may present a fire
hazard.
• The active carbon fi lters are used to purify the air which
is released back into the room.
The fi lters are not washable or re-usable and must be
replaced at least once every four months.
The active carbon fi lter saturation level depends on the
frequency with which the appliance is used, the type of
cooking performed and the regularity with which the anti-
grease fi lters are cleaned.
• Clean the cooker hood frequently, both inside and outside,
using a cloth which has been dampened with denatured
alcohol or neutral, non-abrasive liquid detergents.
• The light on the cooker hood is designed for use during
cooking and not for general room illumination. Extended
use of the light reduces the average duration of the
bulb.
• Replacing halogen light bulbs (Fig. 9).
To replace the halogen light bulbs B, remove the glass
pane C using a lever action on the relevant cracks.
Replace the bulbs with new ones of the same type.
Caution: do not touch the light bulb with bare hands.
•Commands: (Fig.6 A-B) mechanical the key symbols
are explained below:
A = LIGHT
B = OFF
C = SPEED I
D = SPEED II
E = SPEED III
T H E M A N U F A C T U R E R D E C L I N E S A L L
RESPONSIBILITY FOR EVENTUAL DAMAGES
CAUSED BY BREACHING THE ABOVE WARNINGS.
GB
33