Electrical Safety; Residual Risks; Package Contents - DeWalt DW341 Übersetzung Der Originalanweisung

EngLIsh
h ) Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
5) Service
a ) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional Safety Warnings for Jigsaws
• Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the operator
an electric shock.
Use clamps or another practical way to secure and
•
support the workpiece to a stable platform. Holding the
workpiece by hand or against your body leaves it unstable and
may lead to loss of control.
Keep hands away from cutting area. Never reach
•
underneath the workpiece for any reason. Do not
insert fingers or thumb into the vicinity of the reciprocating
blade and blade clamp. Do not stabilize the saw by gripping
the shoe.
Keep blades sharp. Dull or damaged blades may cause
•
the saw to swerve or stall under pressure. Always use the
appropriate type of saw blade for the workpiece material and
type of cut.
When cutting pipe or conduit, make sure that they are
•
free from water, electrical wiring, etc.
Do not touch the workpiece or the blade immediately
•
after operating the tool. They can become very hot.
• Be aware of hidden hazards, before cutting into walls,
floors or ceilings, check for the location of wiring
and pipes.
The blade will continue to move after releasing the
•
switch. Always switch the tool off and wait for the saw blade
to come to a complete standstill before putting the tool down.

Residual Risks


WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA or less.
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
• Impairment of hearing.
• Risk of personal injury due to flying particles.
• Risk of burns due to accessories becoming hot
during operation.
• Risk of personal injury due to prolonged use.
SAVE THESE INSTRUCTIONS
20

Electrical Safety

The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
on the rating plate.
i
Your D WALT tool is double insulated in accordance
e
with EN62841; therefore no earth wire is required.
If the supply cord is damaged, it must be replaced only by
D WALT or an authorised service organisation.
e
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved 3–core
extension cable suitable for the power input of this tool (see
Technical Data).The minimum conductor size is 1.5 mm
maximum length is 30 m.
When using a cable reel, always unwind the cable completely.

Package Contents

The package contains:
1 Jig saw
1 Star wrench
1 Instruction manual
DW341k, DW343k
1 Saw blade
1 Anti-scratch shoe cover
1 Dust extraction shroud
1 Dust extraction adapter
1 Kitbox
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
; the
2