Maintenance - Juliana Compact Montageanleitung

GB
May we congratulate you on your new greenhouse
Dear Customer! DEAR CUSTOMER
Congratulations on purchasing your new
The assembly of your new house requires
greenhouse. It is important that you follow these
a bit of technical knowledge. However, it is
assembly instructions step-by-step.
important that the assembly instructions are
followed strict-ly. The assembly instruction
The assembly instructions are a combination of text
is a combination of text and illustrations. The
and illustrations. The profiles are packed in separate,
profiles are packed in separate numbered packs
numbered packs corresponding to their order of use
in the instructions. Assemble one pack at a time. All corresponding to the order in the assembly
nuts, bolts and fittings are contained in a Box.
instruction. Erect one pack at a time. All nuts
Each pack is specified in separate lists of
and bolts and fittings are found in bag No. 0
components.
(specified on page 12). Each pack is specified in
All detailed illustrations are marked with the
separate lists of components.
following symbols:
All detailed illustrations are marked with
symbols:
Seen from the inside Seen from the outside
Seen from inside Seen from outside.
SOME SAFETY PRECAUTIONS
• Assembly must only be carried out in dry and
calm weather.
Precautions.
• Always wear work gloves when installing the
• Assembly must only be carried out in dry
glazing. Greenhouse glass has sharp edges,
and calm weather.
especially if it breaks.
• Always use working gloves while glazing.
• Assistants and especially children must be
Greenhouse glass has sharp edges,
warned that broken glass is dangerous. Pick
especially if the glass breaks.
up all broken glass at once and remove it with
• Assistants and especially children must be
care.
• We recommend that you wear protective
warned that broken glass is an element of
glasses while fixing the spring wire clips.
danger. Pick up broken glass at once and
• Any ladders that are used must be placed on a
remove it with care.
level surface.
• We recommend to use protective glasses
• It is essential to have an assistant available.
while fixing the spring wire clips.
• Place the ladder on a level support.
PAGE 12: TOOLS
• It is essential to have an assistant.
Assembling the greenhouse requires the tools
shown on page 12.
References
PAGE 13: FOUNDATIONS
The column marked indicates the
No base is included with this product. However, an
page(s) on which the component is used.
original base is available separately. This base is easy
to construct and will guarantee you a stable base for
Page 13:
your greenhouse.
Foundation
If you construct your own base, the specified
The base is not included in this delivery.
measurements must be external measurements.
However, an original base can be bought
The holes must be dug out to below the frost line
(800 mm). Place the assembled base with anchor
separately. It ensures you a stable and easy to
legs over the holes so the anchor legs fit into the
build base.
holes; it takes about 75 litres of concrete to fill up
If you make your own base the measurements
the holes.
indicated must be external measurements.
Make sure the base is completely level and square.
If you buy an original base you furthermore
To square the base, make sure the two diagonal
need about 75 litres of concrete and 6/8
measurements are identical.
plastic-/concrete pipes of about 800 mm which
The width of the front and back gables must also be
are placed in a non-freezing depth for the
identical.
fastening of the corner and middle anchors.
ATTACHMENT TO THE BASE
The base must be 100% level and square; the
If you construct your own base, you must drill holes
latter is ensured by checking that the two
(7mm) in the ground frame between all the vertical
diagonal measurements are equal.
profiles. The greenhouse must then be secured to
the base using screws (A).
Tools
If you use an original base, the greenhouse must be
The mounting of the greenhouse requires the
secured to each vertical bar as shown on drawings
tools shown on page 12.
B/C.
PAGE 14-27: ORDER OF ASSEMBLY
Page 14-27:
Place the components as shown on the illustration
Place the components as shown on the
and assemble in the order shown in the pictures. Do
illustration and assemble in the order shown
not tighten the nuts fully until the entire sub-frame
in the pictures. Do not tighten the nuts
has been assembled.
completely until the front gable construction
has been assembled.
PAGE 24-27: DOORS AND WINDOWS
For easier assembly, we recommend that you oil the
screws for the doors. The glass or polycarbonate for
the door(s) and windows must be fitted at the same
time as the profiles. Page 13:
PAGES 30-37: FITTING OF GLASS/
(Fastening to the base).
POLYCARBONATE
When constructing your own base you have
Important before assembly!
to drill holes (7 mm) in the ground frame
Make sure that the gables and sides are level
between all the vertical frames, the greenhouse
and square and that door(s) and window(s) are
is then fastened to the base with screws (A).
functioning perfectly.
Using an original base the greenhouse is
fastened to each vertical bar as shown on
The best order of assembly for the glass or
polycarbonate is as follows: drawing B/C.
Windows - Roof - Doors - Gables - Sides
Page 24-27:
PAGE 30-33: GLASS INSTALLATION
For an easier assembly we recommend that you
Glass installation (illustrations 1 to 8)
oil the screws for the doors.
Degrease the sheets and frames with spirit.
Start glazing from the bottom, one pane at a time.
Fitting of glass/polycarbonate
Apply a 3mm silicone bead around the vertical
Important before glazing!
frames as indicated (the dotted lines on the
illustration). (A 3mm bead of silicone is sufficient to
ensure maximum adhesion). If you use more silicone
Make sure that gables and sides are level and
than recommended, extra tubes can be purchased.
square, and that door(s) and window(s) are
functioning perfectly.
Spring wire clips and glass-holders must be fitted as
shown.
Best order of assembly:
X = Spring wire clips, > = Glass-holders
1) Windows – 2) Roof – 3) Doors – 4) Gables
– 5) Sides
If you accidentally break a pane, carefully pull the
broken glass outwards and loosen the silicone using
a sharp craft knife.
Page 30-33:
Clean the profile completely before inserting a new
Glazing (illustration 1 to 8)
pane of glass.
Degrease the sheets and frames with spirit.
Start glazing from below, one glass at a time.
PAGE 34-37: POLYCARBONATE INSTALLATION
Apply a 3 mm silicone line on the vertical
The illustrations at the bottom of pages 34/36 show
frames where indicated (dotted lines on
where to fit the polycarbonate sheets and strips. The
the illustration). (A 3 mm line of silicone is
type designation states the length in millimetres. If
adjustment is necessary, use a fine-tooth saw. sufficient to obtain maximum attachment). If
NB! To avoid the growth of algae, prevent the
you do use more than recommended, you can
polycarbonate sheets from coming into contact with
buy extra tubes.
the ground by resting them on a sheet of cardboard.
Spring wire clips and glassholders are to be
A-strips are fitted as shown on pages 35/37. Insert
fitted as shown.
the sheet into the bottom strip, bend the sheet
X = Spring wire clips, > = Glassholders
slightly outwards and insert it into the top strip.
In case of broken glass carefully pull it
M-strips are fitted as shown on pages 35/37. Place
the upper part of the strip under the aluminium
outwards and loosen the silicone by means of a
profile along the full length of the sheet and then
sharp craft knife.
click the strip into position from above.
Clean the profile completely before inserting a
new pane of glass.
U-strips are fitted as shown on pages 35/37.
Page 34-37:
Fit the strip to the sheet and adjust the length.
Mounting of polycarbonate
If desired, the sheets may be sealed against insects. The illustrations at the bottom of page 34/36
Seal the top using aluminium tape or silicone. The
show where to mount the polycarbonate plates
bottom should only be sealed with air-strip tape to
and lists. The type indication states the length
allow condensation to escape (available from your
in mm. A possible adjustment is made by
local dealer).
means of a fine-tooth saw.
NB! To avoid the formation of algae the
Your greenhouse is now fully assembled. However,
polycarbonate sheets must not come into
please note the following:
contact with the ground. Rest them on a piece

MAINTENANCE

of cardboard.
• Grease the doors (hinges and locks).
• Keep the gutters free from leaves, etc.
A-lists are mounted as shown on page 35/37.
• Adjust the windows as necessary.
Put the sheet into the bottom list, bend the
• Replace any broken glass.
sheet slightly outwards and put it in the top list.
• Clean the greenhouse with disinfectant before
and after the growing season.
M-lists are mounted as shown on page 35/37.
Place the upper part of the list under the alu.
WINTER PROTECTION
profile in the whole length of the sheet and
If you anticipate snow during the winter, we
recommend the following winter precautions:
hereafter click on the list from above.
• Support the apex of the roof in the middle.
• Remove any deep snow from the roof.
B
• Take precautions to prevent snow falling from
Sealing of the polycarbonate sheets
a tree or roof, for example.
The sheets may be sealed against insects.
• Remove the cylinders for the automatic
Close the top end off with alu-tape or silicone.
window openers, if fitted (optional extras).
The bottom only with airstrip tape to let
• Secure the door(s) and window(s) to prevent
condensation out (available at your local
wind damage to the greenhouse.
dealer).
WATER AND CONDENSATION
Please note that your greenhouse is not like a Now your greenhouse is completely assembled.
conservatory, for example, and that you should
However, please notice the following:
therefore be aware that the greenhouse may leak
during or after precipitation and that condensation
Maintenance
will occur on the inside of the greenhouse. Good
• Grease doors (hinges and lock).
ventilation will help prevent condensation.
• Clean the gutter for leaves, etc.
• Adjustment of windows.
INSURANCE
• Replacement of broken glass.
Please note that not all insurance companies cover
greenhouses automatically. Please contact your
• Clean the house with disinfectant before
insurance company to ensure that your greenhouse
and after the growing season.
is covered.
Winter Protection
GUARANTEE
In areas with occurrence of snow we
Juliana greenhouses are covered by a 12-year
recommend the following winter protection:
guarantee, which covers the replacement or repair
• Support the roof ridge at the centre of the
of faulty parts. The guarantee does not cover
house.
polycarbonate, glass, transport, assembly, freight,
etc.
• Remove greater snow loads from the roof.
Juliana greenhouses are covered by a two-year
• Take precautions against snow falling
warranty on painted parts, where fitted. Note that
down from for instance a tree or a roof.
marks on the paint may occur due to suspension of
• Dismount the cylinders for the automatic
the profiles.
window openers, if any (optional extras).
The guarantee will be void if the greenhouse is not
• Secure door(s) and window(s) preventing
assembled in accordance with these instructions.
wind damage to the house.
COMPLAINTS
All our greenhouses are built to the highest quality Insurance
standards. However, should you experience any
Please note that not all insurance companies
problems, please contact your dealer at once. When
cover glasshouses automatically. Please
describing the defect, please state the greenhouse
contact your insurance company to ensure an
model, the component number and the quality
insurance coverage.
control number.
Guarantee
Any suspension marks or shiny ends on painted
Juliana grants a guarantee of 12 years which
Juliana profiles will not be visible after the
greenhouse has been assembled.
covers replacement of faulty parts. The
guarantee does not cover polycarbonate, glass,
Congratulations on your new greenhouse, which we
transport, assembly, freight etc.
hope will bring you a lot of pleasure for many years
Juliana grants a guarantee of 2 years on painted
to come.
parts, if any. Note that marks in the painting
may occur due to suspension of the profiles.
Yours sincerely,
The guarantee is invalid if the greenhouse is
not assembled according to these instructions.
Juliana Drivhuse A/S
Complaints
All our greenhouses are built to high standards
of quality. However, should a complaint
occur please contact your dealer at once.
Remember to specify the defect by indicating
the greenhouse model and number of the
component and the quality control number.
USA