Werbung
GB
Dear Customer!
The assembly of your new house requires a bit of
technical knowledge. However, it is important that
the assembly instructions are followed strict-ly. The
assembly instruction is a combination of text and
illustrations. The profiles are packed in separate
numbered packs corresponding to the order in the
assembly instruction. Erect one pack at a time. All
nuts and bolts and fittings are found in bag No. 0
(specified on page 12). Each pack is specified in
separate lists of components.
All detailed illustrations are marked with symbols:
seen from inside
seen from outside.
Precautions.
•
Assembly must only be carried out in dry and
calm weather.
•
Always use working gloves while glazing.
Greenhouse glass has sharp edges,
especially if the glass breaks.
•
Assistants and especially children must be
warned that broken glass is an element of
danger. Pick up broken glass at once and
remove it with care.
•
We recommend to use protective glasses
while fixing the spring wire clips.
•
Place the ladder on a level support.
•
It is essential to have an assistant.
References
The column marked
indicates the page(s)
on which the component is used.
Page 13:
Foundation
The base is not included in this delivery.
The base must be 100% level and square; the
latter is ensured by checking that the two diagonal
measurements are equal.
Tools
The mounting of the greenhouse requires the tools
shown on page 12.
Page 14-26:
Place the components as shown on the illustration
and assemble in the order shown in the pictures.
Do not tighten the nuts completely until the front
gable construction has been assembled.
Page 13:
(Fastening to the base).
When constructing your own base you have to drill
holes (7 mm) in the ground frame between all the
vertical frames, the greenhouse is then fastened to
the base with screws (A).
Using an original base the greenhouse is fastened
to each vertical bar as shown on drawing B.
May we congratulate you on your new Botanica
Page 22-25:
For an easier assembly we recommend that you oil
the screws for the doors /windows.
Fitting of glass/polycarbonate
Important before glazing!
Make sure that gables and sides are
level and square, and that door(s) and
window(s) are functioning perfectly.
Best order of assembly:
1) Windows – 2) Roof – 3) Doors – 4) Gables – 5)
Sides
Page 27-31:
Glazing (illustration 1 to 8)
Degrease the sheets and frames with
acetone.
Start glazing from below, one glass at a time.
Apply a 3 mm silicone line on the vertical frames
where indicated (dotted lines on the illustration).
(A 3 mm line of silicone is sufficient to obtain
maximum attachment). If you do use more than
recommended, you can buy extra tubes.
Spring wire clips and glassholders are to be fitted
as shown.
X = Spring wire clips, > = Glassholders
In case of broken glass carefully pull it outwards
and loosen the silicone by means of a sharp craft
knife.
Clean the profile completely before inserting a new
pane of glass.
Page 30-31:
Mounting of polycarbonate
The illustrations at the bottom of page 31 show
where to mount them. The type indication states
the length in mm. A possible adjustment is made by
means of a fine-tooth saw.
NB! To avoid the formation of algae the
polycarbonate sheets must not come into contact
with the ground. Rest them on a piece of cardboard.
A-lists are mounted as shown on page 31. Put
the sheet into the bottom list, bend the sheet slightly
outwards and put it in the top list.
M-lists are mounted as shown on page 31. Place
the upper part of the list under the alu. profile in the
whole length of the sheet and hereafter click on the
list from above.
Sealing of the polycarbonate sheets
The sheets may be sealed against insects. Close
the top end off with alu-tape or silicone. The bottom
only with airstrip tape to let condensation out
(available at your local dealer).
Now your greenhouse is completely assembled.
However, please notice the following:
Maintenance
•
Grease doors (hinges and lock or doortrack).
•
Clean the gutter for leaves, etc.
•
•
•
Winter Protection
In areas with occurrence of snow we recommend
the following winter protection:
•
•
•
•
•
Insurance
Please note that not all insurance companies
cover glasshouses automatically. Please contact
your insurance company to ensure an insurance
coverage.
Guarantee
Juliana grants a guarantee of 12 years which
covers replacement of faulty parts. The guarantee
does not cover polycarbonate, glass, transport,
assembly, freight etc.
Juliana grants a guarantee of 2 years on painted
parts, if any. Note that marks in the painting may
occur due to suspension of the profiles.
The guarantee is invalid if the greenhouse is not
assembled according to these instructions.
Complaints
All our greenhouses are built to high standards of
quality. However, should a complaint occur please
contact your dealer at once. Remember to specify
the defect by indicating the greenhouse model and
number of the component and the quality control
number.
B
USA
Adjustment of windows.
Replacement of broken glass.
Clean the house with disinfectant before and
after the growing season.
Support the roof ridge at the centre of the
house.
Remove greater snow loads from the roof.
Take precautions against snow falling down
from for instance a tree or a roof.
Dismount the cylinders for the automatic
window openers, if any (optional extras).
Secure door(s) and window(s) preventing wind
damage to the house.
Werbung
