Specifications - Makita BGA402 Bedienungsanleitung

ENGLISH (Original instructions)
1-1. Button
1-2. Red part
1-3. Battery cartridge
2-1. Shaft lock
3-1. Slide switch
4-1. Indication lamp
6-1. Wheel guard
6-2. Bearing box
6-3. Screw
7-1. Lock nut
7-2. Depressed center grinding
wheel/Multi-disc

SPECIFICATIONS

• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
For Model BGA450
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Work mode : surface grinding
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
measured in accordance with the standard test method
and may be used for comparing one tool with another.
The declared vibration emission value may also be used
in a preliminary assessment of exposure.
The declared vibration emission value is used for main
applications of the power tool. However if the power tool
Downloaded from www.Manualslib.com
7-3. Inner flange
8-1. Lock nut wrench
8-2. Shaft lock
10-1. Lock nut
10-2. Abrasive cut-off wheel/diamond
10-3. Inner flange
10-4. Wheel guard for abrasive cut-off
11-1. Exhaust vent
11-2. Inhalation vent
12-1. Limit mark
Model
Wheel diameter
Spindle thread
Rated speed (n) / No load speed (n
Overall length
Net weight
Rated voltage
) : 74 dB(A)
pA
Wear ear protection.
2
) : 8.5 m/s
h,AG
2
manuals search engine
Explanation of general view
wheel
wheel/diamond wheel
BGA402
100 mm
M10
)
0
2.2 kg
D.C. 18V
ENE048-1
is used for other applications, the vibration emission
value may be different.
WARNING:
The vibration emission during actual use of the
•
power tool can differ from the declared emission
ENG104-2
value depending on the ways in which the tool is
used.
Be sure to identify safety measures to protect the
•
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
ENG208-5
Work mode: disc sanding
Vibration emission (a
Uncertainty (K) : 1.5 m/s
For Model BGA452
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
3
13-1. Holder cap cover
13-2. Screwdriver
14-1. Brush holder cap
14-2. Screwdriver
BGA450 BGA452
115 mm
M14
-1
10000 (min )
317 mm
2.2 kg 2.3 kg
D.C. 14.4V D.C. 18V
2
) : 2.5 m/s or less
h,SG
2
) : 73 dB(A)
pA
ENG312-1
ENG104-2