Functional Description; Operation - Makita BUB360 Bedienungsanleitung

(2) Avoid storing battery cartridge in a
container with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
flow, overheating, possible burns and
even a breakdown.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 ﾟ C (122 ﾟ F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1. Charge
completely discharged.
Always stop tool operation and charge the
battery cartridge when you notice less tool
power.
2. Never
cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room
temperature at 10 ﾟ C - 40 ﾟ C (50 ﾟ F - 104 ﾟ F).
Let a hot battery cartridge cool down before
charging it.

FUNCTIONAL DESCRIPTION

CAUTION:
Always be sure that the tool is switched off and the
•
battery cartridge is removed before adjusting or
checking function on the tool.
Installing or removing battery cartridge
Fig.1
Always switch off the tool before insertion or
•
removal of the battery cartridge.
To remove the battery cartridge, withdraw it from
•
the tool while sliding the button on the front of the
cartridge.
To insert the battery cartridge, align the tongue on
•
the battery cartridge with the groove in the housing
and slip it into place. Always insert it all the way
until it locks in place with a little click. If you can see
the red part on the upper side of the button, it is not
locked completely. Insert it fully until the red part
cannot be seen. If not, it may accidentally fall out of
the tool, causing injury to you or someone around
you.
Do not use force when inserting the battery
•
cartridge. If the cartridge does not slide in easily, it
Downloaded from www.Manualslib.com
the battery cartridge
recharge a fully charged
manuals search engine
is not being inserted correctly.
Battery protection system
The battery cartridge is equipped with the protection
system, which automatically cuts off the output power for
its long service life.
The tool may stop during operation when the tool and/or
battery are placed under the following situation. This is
caused by the activation of protection system and does
not show the tool trouble.
When the tool is overloaded:
•
At this time, press the "OFF" button and
remove causes of overload and then press
the "HIGH/LOW" button again to restart.
When the tool does not work even after
pressing the "HIGH/LOW" button, the battery
power auto-stop is still at work. Charge the
battery cartridge before use.
When the remaining battery capacity becomes low:
•
Recharge the battery cartridge.
before
Switch action
Fig.2
To start the tool, simply press the "HIGH/LOW" button. To
switch off, press the "OFF" button. To change the tool
speed, press the "HIGH/LOW" button. The first press on
battery
this button is for high speed and the second press for low
speed and then each press on this button repeats the
high/low speed cycle alternatively.
ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and the
•
battery cartridge is removed before carrying out
any work on the tool.
Installing or removing the long nozzle
Fig.3
To install the long nozzle, push in onto the blower outlet
of the tool all the way.
Fig.4
To remove the long nozzle, press its both buttons and
with the buttons being pressed pull it out.
Installing the shoulder strap
Fig.5
Pull the hanger out of the tool.
Hook the shoulder strap onto the hanger of the tool.
Before use, adjust the length of strap so that it is easy to
work with it.

OPERATION

Blowing
Fig.6
Hold the blower firmly with a hand and perform the
blowing operation by moving it around slowly
When blowing around a building, a big stone or a vehicle,
5