Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Chapter 3. Routine Maintenance
Table 1: Where to Put Marks On a Calendar
Hours /
Week
1
2
3
4
5
Up to 40 2
2
2
2
3
41 - 60
2
2
3
2
2
61 - 80
2
2
3
2
3
81 - 100
2
3
2
3
2
101 - 120 2
3
2
3
4
121 - 140 2
3
2
3
4
Hours /
Week
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Up to 40 2
2
2
2
3
41 - 60
2
2
3
2
2
Maintenance Summary
3.1.2.
The tables in this section give the routine maintenance items for your machine. Each table is for
one type of procedure (example: apply grease to bearings and bushings). The top of the table
gives the general procedure. The "More Data" column gives special instructions if necessary.
* If the machine operates more than 12 hours each day, do the "day" items two times each day.
Do the other items at the given hours or on the days that you show on a calendar (see Section 1).
Do all items in all tables for the maintenance intervals that apply (for example, day, 40 to 60
hours, and 200 hours).
The sections that follow the maintenance summary give more data about the maintenance items.
Tip:
After you know this data, it is only necessary to look at the summary to do the maintenance.
Table 2: Guards and Related Components
Examine. If a component is damaged, missing, or not set, correct this immediately to prevent injury.
Mark
Do this each
1 2 3 4 5 6
x
day*
x
day*
x
200 hours
x
day*
x
200 hours
x
600 hours
x
40 to 60 hours safety circuit for the gates in
PELLERIN MILNOR CORPORATION
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
2
2
2
2
3
2
2
2
3
2
2
4
2
2
2
4
2
2
3
2
2
4
2
3
2
3
2
5
2
3
2
3
5
2
3
3
2
3
5
2
3
2
Week Number, continued
2
2
2
2
3
2
2
2
3
2
2
6
Component
guards, covers
safety placards
fasteners
maintenance key switch
anchor bolts and grout
mechanical brake
the fence that goes around the
path of the shuttle conveyor
Week Number
2
2
4
2
2
2
2
3
2
2
2
3
2
2
3
2
5
2
3
2
2
2
3
2
3
2
4
2
2
3
4
2
3
2
3
3
4
3
2
3
6
2
2
4
2
2
2
2
Speak to your dealer or Milnor for
replacement components.
Fasteners must be tight.
See
Figure
13. Must be set to "Safe
Operation"
Grout must be good. Bolts must be tight.
See
Supplement
mechanical brake. If it does not operate
correctly, repairs are necessary. Speak to your
dealer or Milnor. This is not routine
maintenance.
See
Supplement
it does not operate correctly, repairs are
necessary. This circuit is provided by others.
21
3
2
2
2
2
3
2
5
2
2
3
2
2
2
3
2
4
2
2
3
2
3
2
3
2
6
6
repeat
repeat
3
2
2
2
2
3
2
repeat
More Data
6. Do a test of the
4. Do a test of the circuit. If
2
2
2
5
3
2
2
4
2
3
2
6
repeat
2
2
2
6
Werbung
Kapitel
Inhaltsverzeichnis
