RADEMACHER RolloTube S-line Sun DuoFern Kurzanleitung Zur Montage- Und Erstinbetriebnahme Seite 2

RolloTube S-line Sun DuoFern
Brief instructions for installation and initial commissioning
Risk of fatal electric shock when touching electrical
components.
◆ The electrical connection of the tubular motor and all work
on the electrical systems may only be undertaken by an
authorised qualified electrician.
◆ Carry out all installation and connection work only in an
isolated, de-energised state.
◆ Disconnect all phases of the mains power lead and se-
cure it to prevent any reconnection.
◆ Check that the system is de-energised.
Requirements for the correct execution of the following
functions:
Self-learning operation:
◆ The awning requires a fixed end stop when closed in order
to be able to learn the end point.
◆ The extended end point must first be learned or set.
◆ The driver adapter must be mounted with a freewheel
mechanism.
Blockage detection:
◆ The awning must move easily and freely.
Briefly press the set button on the drive head
until the tubular motor starts up briefly. You now
have 120 seconds time to activate the log-on
mode of a DuoFern device.
Please read the operating manual for the
DuoFern device.
The RolloTube S-line sun DuoFern tubular motors are
self-learning motors at both end positions. This eliminates the
need to set the end points or a teach-in run.
1.
Switch on the mains power supply. The RolloTube S-line
Sun DuoFern is ready for operation immediately.
2.
First extend and then retract the awning.
t
▲
The end positions are automatically learned
during the first drive cycles.
3.
Subsequently check the direction of travel of the roller
shutter, if the RolloTube S-line Sun DuoFern is being
operated using a switch or button. Switch the lines for the
rotation direction if the direction of travel is wrong.
DANGER!
Example connection with a switch / button
Set button
Connect the motor cable to the connecting cable
(2.5 m) supplied by means of a connector and
make the connection according to the following
wiring configuration.
Green/yellow (a) = PE
Blue
Grey
Black
Brown
* The black and brown wires (direction of travel 1 and 2) are not
required for radio operation and therefore not connected.
There is also a risk of fatal injury from crush-ing result-
ing from uncontrolled starting of the drive.
◆ Never attempt to manually stop the motor/awning in the
event of uncontrolled movement.
Before you begin, please read this detailed operating manual
of the RolloTube S-line Sun DuoFern through completely and
follow all the safety instructions and installation instructions.
Fabric relief:
◆ This function is only active if the upper end point is set to automatic/
self-learning.
Obstacle detection:
◆ The driver adapter must be mounted with a freewheel
mechanism.
Fabric tensioning::
◆ The fabric tensioning function is always active after the first run cycles,
after both the self-taught and manual end point setting.
protective terminal
(b) = N neutral terminal
(c) = L continuous phase
(d) = direction of travel 1 *
(e) = direction of travel 2 *
Initial installation
At the initial installation, the roller shutter engineer can carry
out the end point setting with the help of the set button on
the motor or with a commercially available universal setting
cable, see operating manual of the RolloTube S-line Sun Duo-
Fern.
Universal setting cable
2
1
DANGER!
Set button
5
Switch or button
a b
3
L
230 V ~
N
50 Hz
PE
Pin assignment:
The universal setting cable is connec-
ted with the same colours as the motor
3
connecting cable of the RolloTube S-line
Sun DuoFern, see above.
Button assignment:
Button 1 = direction of travel (I / II)
Button 2 = set button (III)
Button 3 = continuous phase
(ON/SET)
VBD 694-7 (05.20)
c d e