General Information; Electrical Connections - Camille Bauer KINAX HW730 Betriebsanleitung

Device Sub-
Device
ID ID
0x01 0x00 VR660
0x02 0x00 A200R
0x03 0x01 CAM
0x04 0x00 APLUS
0x05 0x00 V604s
0x05 0x01 VB604s
0x05 0x02 VC604s
0x05 0x03 VQ604s
0x07 0x00 VS30 Temperature transmitter
0x08 0x00 DM5S Multi transmitter standard
0x08 0x01 DM5F Multi transmitter fast
0x08 0x02 DM5E Multi transmitter energy
0x08 0x03 DM5SC Multi transmitter monitoring
0x09 0x00 CAM Quality System analysis ___________________
0x0A 0xFF HW730 Transmitters for angular position
0x0B 0xFF CAM Profinet CAM Ethernet Buscard with Profinet
6.3 Process image
Definition of all volatile and non-volatile parameters and
variables.
6.4 Measured values
The measured angle is available in two different formats.
Adress Length Designation
40001 2 PHI_FLOAT
40003 1 PHI_INT

6.5 General information

Adresse Length Designation
40101 1 FW_REVISION UINT16
40102 1 FW_VERSION
40103 1 MB_VERSION
40104 1 RESERVE
40105 2 SERIAL
6.6 Configuration
Adresse Length Designation
40201 1 CONFIG
18
Description
Temperature controller
Display
Universal measuring unit for heavy current
variables
Multifunctional display
Universal transmitter
Universal transmitter multi in/out
Universal transmitter second Relay
Universal transmitter fast setting time
Typ Description
FLOAT Measured value in degrees
(0.0° ≤ PHI_FLOAT < 360.0°)
UINT16 The value for the 360°
angle can be configured via
NO_STEPS.
(0 ≤ PHI_INT < NO_STEPS)
Typ Description
Revisions number
UINT16 Firmware version
Byte 1 Byte 0
v 1.00
1.00: Version number
Hexadecimal representation of
the version number
UINT16 Version of the Modbus image.
UINT16 Reserved
UINT32 Serial number of the device
Typ Description
UINT16 Bit 0: Sense of rotation
0 clockwise
1 counterclockwise
Bit 2 ... 15: Reserved
Bit 8 ... 15: Reserved
Operating Instructions HW730 Be
40202 1 NO_STEPS
40203 2 ZERO
NO_STEPS refers to the subdivision of the entire measuring
range of 0...360 into number of steps.
(E.g. NO_STEPS 100 means to divide 0...360 into 100 parts
of 3.6°)
Adress Length Designation
10001 1 SET_ZERO
6.7 Network configuration IPv4
Adress Length Designation
40301 2 IPv4
40303 2 SUBNETv4
40305 2 GATEWAYv4
6.11 TCP-Port für Modbus/TCP
Port 502 is always used for Modbus/TCP as a standard.
HW730-ETH is always accessible via this port. Further con-
nections can be alternatively realised via the following con-
figured port.
Adresse Length Designation
40315 1 TCP_PORT
6.12 Name of device
A name may be allocated to each device. This simplifies the
identification of the device via the search service.
Adresse Length Designation
40401 16 NAME
7. Mounting
See page 23.

8. Electrical connections

For connecting the external wires, the transmitter has a
plug connector M12x1 / 4 poles d-coded or a cable glands
M16x1.5. During the version with a cable glands the con-
nection via a spring-type terminal block made in accordance
with diagram of connections.
Permissible cable:
Cable length:
Connection allocation plug M12/4-pole d-coded
1
2
4
3
Number of steps per 360°
UINT16
Default: 4096
Zero point
FLOAT
Default: 0.0
Typ Description
Determine current angle to be
COIL
the zero point
Typ Description
UINT32 IP-Adress
UINT32 Subnetmaske
UINT32 Standard-Gateway
Typ Description
UINT16 Alternative Modbus/TCP port
Typ Description
Identification of the device
in text form
CHAR[32] Allowed characters:
'A'...'Z', 'a'...'z', '_',
0-terminated
Ethernet CAT5
100m
Pin Signal
1 Rx+
2 Tx+
3 Rx-
4 Tx-
Camille Bauer Metrawatt