Important Advice - Innotek SD-2100E Bedienungsanleitung

2100268-1_A_Manual SD-2100E.qxp
Quick Start Guide
Step 5
Charge Collar
Position the collar receiver in the charging cradle located on the top of the wall trans-
mitter. Orient the light on the collar receiver toward the end of the charging cradle
marked with an arrow and identified on the label.
Step 6
Test Your Fence
Set your FIELD WIDTH ADJUSTMENT KNOB to the 9 o'clock position. Using the
supplied test light, walk the dog's collar up to the fence wire. Listen for the
warning tone and look for the test light to light. Try a number of different places
around the fenced area to verify the range is consistent.
Step 7
Bury Fence Wire
Dig the trench 7.6cm deep with a flat edge spade. Or, it is faster to use a gas-
powered edger. Digging the trench at an angle helps keep the wire in the
ground as you place it. Place flags at edge of selected boundary field where the
warning tone is first heard, NOT at wire.
Step 8
Train Your Dog
Watch the training video and follow the training steps
outlined in the separate Training and Troubleshooting
Guide. Your dog may respond immediately to the train-
ing, however, continue to follow the enclosed Training
Guide to fully train your dog. The convenience that your
new fence offers plus the added safety for your dog are
well worth the time invested.
Downloaded from www.Manualslib.com
7/7/2005 2:15 PM Page 2
(continued)
collar receiver light to this end
1. Field Width
Adjustment Control
2.
manuals search engine

IMPORTANT ADVICE

1. Read the complete manual and follow all directions. This
SD-2100E
includes the Training and Troubleshooting Guide.
2. This device is intended for use only on dogs. Never
attempt to use it for any purpose not described in
this manual.
3. Never perform set-up procedures while the collar is
on your dog.
4. Any collar worn for extended periods can cause a
condition similar to bedsores, known as Pressure
Necrosis. To reduce the possibility, you must do
the following:
• Never leave the collar on the dog for more than 12
hours per day.
• Check the fit to prevent excessive pressure; you
should be able to insert one finger between the
collar strap and your dog's skin.
• Examine the dog's neck daily for any signs of a
rash or a sore.
• Wash the dog's neck area and the probes of the
collar weekly with a damp cloth.
• If the condition persists beyond 24 hours,
see your veterinarian.
5. Always use the rubber insulators between the
collar strap and probes to provide insulation
in damp conditions.
6. Other collars and metal tags should be removed
as they may interfere with proper operation.
7. Do not attempt to dismantle or repair any
components of this system; doing so will void the
warranty in full. The computerized circuitry should
be serviced only by an authorized expert.
8. Realize that because dogs have unique tempera-
ments, there is no way of knowing how your dog
will react to the introduction of a containment system.
For the safety of your dog, a long lead should be used
during initial training so you have control of the situation.
9. If you have reason to believe that your dog may
pose a danger to others, harm itself, or react
adversely to the collar, do not rely solely on this
product to train your dog. If your dog shows signs
of growling, snarling or biting while using the collar,
stop immediately. Aggression in dogs has many
causes. We recommend that you consult a knowl-
edgeable professional dog trainer or animal
behaviorist with experience with aggressive dogs
if your dog has shown any of these characteristics.
10. Occasionally, a dog cannot be trained to respond
to a containment collar. Sometimes even a properly
trained dog may disobey a command. Therefore,
Invisible Technologies, its distributors, and dealers
cannot guarantee that the system will in all cases keep
the customer's animal from disobeying commands.
LIMITED INTERNATIONAL WARRANTY
Innotek™ warrants that its products will be free from
defects in material and workmanship under normal use
for one year from the date of original consumer purchase.
This Limited Warranty is offered only to the original con-
sumer purchaser. This Limited Warranty is subject to the
condition that any covered defect occurs under normal
conditions of use and maintenance and that Innotek
receives prompt written notice of the discovery of the
defect within the Limited Warranty period. It does not
apply to damage or failures that result from physical
abuse or misuse of the product. The Limited Warranty is
void if any attempts are made to alter or repair the prod-
uct prior to returning it to the facility within the Limited
Warranty period. This Limited Warranty does not cover
lost parts or broken probe studs.
During the Limited Warranty period, products covered by
the Limited Warranty will be repaired by an Innotek-
authorized Service Center for a nominal processing fee.
Authorized Service Centers are located throughout the
world. Shipping costs to the Service Center are not cov-
ered by this Limited Warranty. The returned item must be
accompanied by a copy of the original receipt showing
the place and date of purchase.
EXCEPT AS SPECIFICALLY SET FORTH HEREIN, THERE
ARE NO WARRANTIES, REPRESENTATIONS, PROMISES
OR ASSURANCES BY INNOTEK, EITHER EXPRESSED OR
IMPLIED, WHETHER BY LAW, CUSTOM PREVIOUS TRANS-
ACTION OR OTHERWISE, INCLUDING WITHOUT LIMITA-
TION, WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE WITH REGARD TO THE
PRODUCT. INNOTEK'S LIABILITY IS SOLELY AS STATED
HEREIN AND NO OTHER LIABILITY SHALL EXIST,
WHETHER BY NEGLIGENCE, STRICT LIABILITY, TORT OR
ANY OTHER CAUSE OR ACTION. ALL LIABILITIES FOR
INNOTEK STATED HEREIN ARE THE SOLE AND EXCLUSIVE
REMEDIES OF THE ORIGINAL CONSUMER PURCHASER. IN
NO EVENT SHALL INNOTEK BE LIABLE FOR ANY CONSE-
QUENTIAL OR INCIDENTAL DAMAGES, OR ANY OTHER
TYPE OF DAMAGE WHICH MAY BE CAUSED IN WHOLE OR
IN PART BY ANY FAILURE, DEFECT OR PROBLEM OF THE
PRODUCT.
Innotek products are not substitutes for traditional obedi-
ence training. Innotek does not guarantee the effective-
ness of its products due to variances in canine personal-
ity, temperament and influences beyond Innotek's control.
If services are required, please contact the nearest
Service Center as advised below to obtain a Return
Merchandise Authorization (RMA) number and return
instructions. If the return request is approved, please send
the defective part or the complete system by insured car-
rier to the specified address. Shipping costs are not cov-
ered.
3.