Specifications; Polisher Safety Warnings - Makita 9227CB Betriebsanleitung

ENGLISH
(Original instructions)
1 Shaft lock
2 Switch trigger
3 Lock button
4 Speed adjusting dial
5 Protrusion of loop handle
6 Matching hole in gear housing

SPECIFICATIONS

Model
Max. capacities
Wool pad .......................................................... 180 mm
Spindle thread ........................................................ M14
Rated speed (n) /
No load speed (n
Overall length ...................................................... 470 mm
Net weight .............................................................. 3.1 kg
Safety class .............................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for polishing, smoothing before
painting, finishing surfaces, and removing rust and paint.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.

POLISHER SAFETY WARNINGS

Safety Warnings Common for Polishing Operation:
1. This power tool is intended to function as a
polisher. Read all safety warnings, instructions,
illustrations and specifications provided with
this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
2. Operations such as grinding, sanding, wire
brushing or cutting-off are not recommended to
be performed with this power tool. Operations for
which the power tool was not designed may create a
hazard and cause personal injury.
3. Do not use accessories which are not specifi-
cally designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
4
Downloaded from www.Manualslib.com
Explanation of general view
7 Loop handle
8 Bolt
9 Hex wrench
10 Wool pad
11 Sleeve 18
12 Backing pad
) ................................. 0 – 3,000 min
0
manuals search engine
4. The rated speed of the accessory must be at
least equal to the maximum speed marked on
9227CB
the power tool. Accessories running faster than
their rated speed can break and fly apart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating of
–1
your power tool. Incorrectly sized accessories can-
not be adequately guarded or controlled.
6. The arbour size of backing pads or any other
accessory must properly fit the spindle of the
/II
power tool. Accessories with arbour holes that do
not match the mounting hardware of the power tool
will run out of balance, vibrate excessively and may
cause loss of control.
7. Do not use a damaged accessory. Before each
use inspect the accessory such as backing pad
for cracks. If power tool or accessory is dropped,
inspect for damage or install an undamaged
accessory. After inspecting and installing an
accessory, position yourself and bystanders
away from the plane of the rotating accessory
and run the power tool at maximum no-load
speed for one minute. Damaged accessories will
normally break apart during this test time.
8. Wear personal protective equipment. Depending
on application, use face shield, safety goggles
or safety glasses. As appropriate, wear dust
GEA010-1
mask, hearing protectors, gloves and workshop
apron capable of stopping small abrasive or
workpiece fragments. The eye protection must be
capable of stopping flying debris generated by vari-
ous operations. The dust mask or respirator must be
capable of filtrating particles generated by your oper-
ation. Prolonged exposure to high intensity noise
may cause hearing loss.
9. Keep bystanders a safe distance away from work
GEB038-2
area. Anyone entering the work area must wear
personal protective equipment. Fragments of work-
piece or of a broken accessory may fly away and
cause injury beyond immediate area of operation.
10. Position the cord clear of the spinning acces-
sory. If you lose control, the cord may be cut or
snagged and your hand or arm may be pulled into
the spinning accessory.
11. Never lay the power tool down until the acces-
sory has come to a complete stop. The spinning
accessory may grab the surface and pull the power
tool out of your control.
12. Do not run the power tool while carrying it at
your side. Accidental contact with the spinning
accessory could snag your clothing, pulling the
accessory into your body.
13. Regularly clean the power tool's air vents. The
motor's fan will draw the dust inside the housing and
excessive accumulation of powdered metal may
cause electrical hazards.
13 Spindle
14 Limit mark
15 Screwdriver
16 Brush holder cap