Optional Accessories - Makita DRS780 Betriebsanleitung

Lanyard (tether strap) connection
6DIHW\ ZDUQLQJV VSHFL¿F IRU XVH DW KHLJKW
Read all safety warnings and instructions. Failure to follow
WKH ZDUQLQJV DQG LQVWUXFWLRQV PD\ UHVXOW LQ VHULRXV LQMXU\
1. Always keep the tool tethered when working "at
height". Maximum lanyard length is 2 m (6.5 ft).
2. Use only with lanyards appropriate for this tool
type and rated for at least 6.5 kg (14.4 lbs).
3. Do not anchor the tool lanyard to anything on
your body or on movable components. Anchor
the tool lanyard to a rigid structure that can
withstand the forces of a dropped tool.
4. Make sure the lanyard is properly secured at
each end prior to use.
5. Inspect the tool and lanyard before each use
for damage and proper function (including
fabric and stitching). Do not use if damaged or
not functioning properly.
6. Do not wrap lanyards around or allow them to
come in contact with sharp or rough edges.
7. Fasten the other end of the lanyard outside the
working area so that a falling tool is held securely.
8. Attach the lanyard so that the tool will move away
from the operator if it falls. Dropped tools will swing on
WKH ODQ\DUG ZKLFK FRXOG FDXVH LQMXU\ RU ORVV RI EDODQFH
 Do not use near moving parts or running
machinery. )DLOXUH WR GR VR PD\ UHVXOW LQ D FUXVK
RU HQWDQJOHPHQW KD]DUG
10. Do not carry the tool by the attachment device
or the lanyard.
11. Only transfer the tool between your hands
while you are properly balanced.
12. Do not attach lanyards to the tool in a way that keeps
guards, switches or lock-offs from operating properly.
13. Avoid getting tangled in the lanyard.
14. Keep lanyard away from the cutting area of the tool.
15. Use multi-action and screw gate type carabineers.
Do not use single action spring clip carabineers.
16. In the event the tool is dropped, it must be tagged
and removed from service, and should be inspected
by a Makita Factory or Authorized Service Center.
Fig.29: 1. +ROH IRU ODQ\DUG WHWKHU VWUDS
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed before
attempting to perform inspection or maintenance.
CAUTION:
Clean out the upper and lower guards
to ensure there is no accumulated sawdust which may
impede the operation of the lower guarding system. A
GLUW\ JXDUGLQJ V\VWHP PD\ OLPLW WKH SURSHU RSHUDWLRQ ZKLFK
FRXOG UHVXOW LQ VHULRXV SHUVRQDO LQMXU\ 7KH PRVW HIIHFWLYH
ZD\ WR DFFRPSOLVK WKLV FOHDQLQJ LV ZLWK FRPSUHVVHG DLU If
the dust is being blown out of the guards be sure the
proper eye and breathing protection is used.
NOTICE:
Never use gasoline, benzine, thinner, alcohol
or the like. Discoloration, deformation or cracks may result.
Adjusting 0°-cut accuracy
7KLV DGMXVWPHQW KDV EHHQ PDGH DW WKH IDFWRU\ %XW LI LW LV
RII \RX FDQ DGMXVW LW DV WKH IROORZLQJ SURFHGXUH
1. 6OLJKWO\ ORRVHQ WKH OHYHU RQ RQ WKH EHYHO VFDOH
plate.
2. Make the base perpendicular to the blade using
D WULDQJXODU UXOH RU VTXDUH UXOH E\ WXUQLQJ WKH DGMXVWLQJ
bolt.
Fig.30: 1. Triangular rule 2. $GMXVWLQJ EROW
3. Tighten the lever and then make a test cut to
check the verticalness.
To maintain product SAFETY and RELIABILITY,
UHSDLUV DQ\ RWKHU PDLQWHQDQFH RU DGMXVWPHQW VKRXOG
EH SHUIRUPHG E\ 0DNLWD $XWKRUL]HG RU )DFWRU\ 6HUYLFH
&HQWHUV DOZD\V XVLQJ 0DNLWD UHSODFHPHQW SDUWV
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use with your Makita tool
VSHFL¿HG LQ WKLV PDQXDO 7KH XVH RI DQ\ RWKHU
accessories or attachments might present a risk of
LQMXU\ WR SHUVRQV 2QO\ XVH DFFHVVRU\ RU DWWDFKPHQW
for its stated purpose.
,I \RX QHHG DQ\ DVVLVWDQFH IRU PRUH GHWDLOV UHJDUG-
LQJ WKHVH DFFHVVRULHV DVN \RXU ORFDO 0DNLWD 6HUYLFH
Center.
• Circular saw blade
• Wrench
‡ 5LS IHQFH *XLGH UXOH
‡ 0DNLWD JHQXLQH EDWWHU\ DQG FKDUJHU
NOTE: 6RPH LWHPV LQ WKH OLVW PD\ EH LQFOXGHG LQ WKH
WRRO SDFNDJH DV VWDQGDUG DFFHVVRULHV 7KH\ PD\
GLIIHU IURP FRXQWU\ WR FRXQWU\
14 ENGLISH