Makita DRS780 Betriebsanleitung Seite 12

Adjusting depth of cut
CAUTION:
After adjusting the depth of cut,
always tighten the lever securely.
Loosen the lever on the depth guide and move the base up or down.
$W WKH GHVLUHG GHSWK RI FXW VHFXUH WKH EDVH E\ WLJKWHQLQJ WKH OHYHU
For cleaner, safer cuts, set cut depth so that no more
WKDQ RQH EODGH WRRWK SURMHFWV EHORZ ZRUNSLHFH 8VLQJ
proper cut depth helps to reduce potential for danger-
RXV .,&.%$&.6 ZKLFK FDQ FDXVH SHUVRQDO LQMXU\
Fig.12: 1. Lever
Bevel cutting
CAUTION:
After adjusting the bevel angle,
always tighten the lever securely.
/RRVHQ WKH OHYHU DQG VHW IRU WKH GHVLUHG DQJOH E\ WLOWLQJ
DFFRUGLQJO\ WKHQ WLJKWHQ WKH OHYHU VHFXUHO\
Fig.13: 1. Lever
Positive stopper
The positive stopper is useful for setting the des-
LJQDWHG DQJOH TXLFNO\ 7XUQ WKH SRVLWLYH VWRSSHU VR
WKDW WKH DUURZ RQ LW SRLQWV \RXU GHVLUHG EHYHO DQJOH
ƒƒƒ  /RRVHQ WKH OHYHU DQG WKHQ WLOW WKH WRRO
base until it stops. The position where the tool base
VWRSV LV WKH DQJOH \RX VHW ZLWK WKH SRVLWLYH VWRSSHU
Tighten the lever with the tool base at this position.
Fig.14: 1. Positive stopper
Sighting
For straight cuts, align the 0° position on the front of the base with
\RXU FXWWLQJ OLQH )RU ƒ EHYHO FXWV DOLJQ WKH ƒ SRVLWLRQ ZLWK LW
Fig.15: 1. &XWWLQJ OLQH ƒ SRVLWLRQ 2. Cutting line
ƒ SRVLWLRQ
Switch action
WARNING:
Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
WARNING:
NEVER defeat the lock-off button
by taping down or some other means. A switch with
D QHJDWHG ORFNRII EXWWRQ PD\ UHVXOW LQ XQLQWHQWLRQDO
RSHUDWLRQ DQG VHULRXV SHUVRQDO LQMXU\
WARNING:
NEVER use the tool if it runs when you
simply pull the switch trigger without pressing the lock-off
button. $ VZLWFK LQ QHHG RI UHSDLU PD\ UHVXOW LQ XQLQWHQWLRQDO
RSHUDWLRQ DQG VHULRXV SHUVRQDO LQMXU\ 5HWXUQ WRRO WR D 0DNLWD
service center for proper repairs BEFORE further usage.
7R SUHYHQW WKH VZLWFK WULJJHU IURP EHLQJ DFFLGHQWDOO\
pulled, a lock-off button is provided. To start the tool,
depress the lock-off button and pull the switch trigger.
Release the switch trigger to stop.
Fig.16: 1. Switch trigger 2. Lock-off button
NOTICE:
Do not pull the switch trigger hard without
pressing in the lock-off button. This can cause switch breakage.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Removing or installing circular saw
blade
CAUTION:
Be sure the circular saw blade is
installed with teeth pointing up at the front of the
tool.
CAUTION:
Use only the Makita wrench to
install or remove the circular saw blade.
To remove the circular saw blade, press the shaft lock
IXOO\ VR WKDW WKH FLUFXODU VDZ EODGH FDQQRW UHYROYH DQG
use the wrench to loosen the hex bolt clockwise. Then
UHPRYH WKH KH[ EROW ULQJ FRXQWU\ VSHFL¿F  RXWHU ÀDQJH
and circular saw blade.
Fig.17: 1. Shaft lock 2. Wrench
For tool without the ring
Fig.18: 1. Hex bolt 2. 2XWHU ÀDQJH 3. Circular saw
blade 4. ,QQHU ÀDQJH
For tool with the ring
Fig.19: 1. Hex bolt 2. 2XWHU ÀDQJH 3. Circular saw
blade 4. Ring 5. ,QQHU ÀDQJH
To install the circular saw blade, follow the removal
procedure in reverse.
)RU WRRO ZLWK WKH LQQHU ÀDQJH IRU
other than 15.88 mm hole-diameter
saw blade
7KH LQQHU ÀDQJH KDV D FHUWDLQ GLDPHWHU SURWUXVLRQ RQ
one side of it and a different diameter protrusion on the
other side. Choose a correct side on which protrusion
¿WV LQWR WKH VDZ EODGH KROH SHUIHFWO\ 0RXQW WKH LQQHU
ÀDQJH RQWR WKH PRXQWLQJ VKDIW VR WKDW WKH FRUUHFW VLGH
RI SURWUXVLRQ RQ WKH LQQHU ÀDQJH IDFHV RXWZDUG DQG WKHQ
SODFH VDZ EODGH DQG RXWHU ÀDQJH
Fig.20: 1. Mounting shaft 2. ,QQHU ÀDQJH 3. Circular
saw blade 4. 2XWHU ÀDQJH 5. Hex bolt
WARNING:
BOLT COUNTERCLOCKWISE SECURELY. Also
be careful not to tighten the bolt forcibly. Slipping
your hand from the hex wrench can cause a per-
sonal injury.
WARNING:
RQ WKH LQQHU ÀDQJH WKDW LV SRVLWLRQHG RXWVLGH ¿WV
into the saw blade hole "a" perfectly. Mounting the
blade on the wrong side can result in the dangerous
vibration.
12 ENGLISH
BE SURE TO TIGHTEN THE HEX
Make sure that the protrusion "a"