Makita DRS780 Betriebsanleitung Seite 11

Overload protection
When the tool is operated in a manner that causes it to
GUDZ DQ DEQRUPDOO\ KLJK FXUUHQW WKH WRRO DXWRPDWLFDOO\
stops. In this situation, turn the tool off and stop the
application that caused the tool to become overloaded.
Then turn the tool on to restart.
Overheat protection
When the tool is overheated, the tool stops automati-
FDOO\ DQG WKH EDWWHU\ LQGLFDWRU EOLQN DERXW  VHFRQGV
In this situation, let the tool cool down before turning the
tool on again.
On
Overload alert
If the tool is operated with excessive load, the mode
indicator will blink in green. The mode indicator stops
EOLQNLQJ DQG WKHQ OLJKWV XS RU WXUQV RII LI \RX UHGXFH WKH
load on the tool.
Fig.8: 1. Mode indicator
Overdischarge protection
:KHQ WKH EDWWHU\ FDSDFLW\ EHFRPHV ORZ WKH WRRO VWRSV
DXWRPDWLFDOO\ ,I WKH SURGXFW GRHV QRW RSHUDWH HYHQ
when the switches are operated, remove the batteries
from the tool and charge the batteries.
Indicating the remaining battery
capacity
Fig.9: 1. %DWWHU\ LQGLFDWRU 2. Check button
3UHVV WKH FKHFN EXWWRQ WR LQGLFDWH WKH UHPDLQLQJ EDWWHU\
FDSDFLWLHV 7KH EDWWHU\ LQGLFDWRUV FRUUHVSRQG WR HDFK
EDWWHU\
Battery indicator status
On Off
Blinking
Remaining
battery
capacity
Blinking
50% to 100%
20% to 50%
0% to 20%
Charge the
EDWWHU\
11 ENGLISH
Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
Fig.10: 1. Indicator lamps 2. Check button
3UHVV WKH FKHFN EXWWRQ RQ WKH EDWWHU\ FDUWULGJH WR LQGL-
FDWH WKH UHPDLQLQJ EDWWHU\ FDSDFLW\ 7KH LQGLFDWRU ODPSV
light up for a few seconds.
Indicator lamps
Lighted Off
NOTE: Depending on the conditions of use and the
DPELHQW WHPSHUDWXUH WKH LQGLFDWLRQ PD\ GLIIHU VOLJKWO\
IURP WKH DFWXDO FDSDFLW\
Automatic speed change function
This tool has "high speed mode" and "high torque
mode".
7KH WRRO DXWRPDWLFDOO\ FKDQJHV WKH RSHUDWLRQ PRGH
depending on the work load. When the work load is low,
the tool will run in the "high speed mode" for quicker
cutting operation. When the work load is high, the tool
will run in the "high torque mode" for powerful cutting
operation.
Fig.11: 1. Mode indicator
The mode indicator lights up when the tool is running in
"high torque mode".
Mode indicator status
On
Remaining
capacity
Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
EDWWHU\
7KH EDWWHU\
PD\ KDYH
malfunctioned.
Operation mode
Off
High speed mode
High torque mode