Air Filter (Mod. Honda Gxv 630; 660; 690) (26); Air Filter (Mod. B&S 8270) (29X); Air Filter (Mod. B&S Vanguard 18Hp) (27X); Spark Plug - Stiga Park 4WD serie Gebrauchsanweisung

EN
NOTE! The filters should be cleaned/re-
placed more often if the machine ope-
rates on very dusty ground Remove/
install the air filters as follows:
9 10 1 Air filter (Mod. Honda GXV 630; 660;
690) (26)
1. Clean carefully around the air filter housing.
2. Remove the air filter cover (26:D) by relea-
sing the two lateral tabs.
3. Dismantle the pre-filter assembly (26:C).
Remove the paper filter (26:B). Make sure
that no dirt gets into the carburettor. Clean
the air filter housing.
4. Clean the paper filter by tapping it gently
against a flat surface. If the filter is very dirty,
replace it.
5. Assemble the filter by performing the above
instructions in reverse order.
Compressed air or petroleum-based solvents such
as kerosene must not be used for cleaning the pa-
per filter insert. This will damage the filter.
Do not use compressed air for cleaning the paper
filter insert. The paper filter insert must not be oiled.
9 10 2 Air filter (Mod. B&S 8270) (29X)
1. Carefully clean around the air filter cover.
2. Remove the air filter cover (29X:A) by un-
screwing the two knobs (29X:B).
3. Dismantle the filter assembly (29X:C). Extract
the pre-filter (29X:D).
4. Clean the paper filter by tapping it gently
against a flat surface. If the filter is very dirty,
replace it.
5. Clean the pre-filter. If the filter is very dirty,
replace it.
6. Assemble the filter by performing the above
instructions in reverse order.
9 10 3 Air filter (Mod. B&S VANGUARD
18HP) (27X)
1. Carefully clean around the air filter cover.
2. Remove the air filter cover (27X:A) by remo-
ving the two clamps.
3. Dismantle the filter assembly (27X:B). The
prefilter is placed over the air filter. Make sure
that no dirt gets into the carburettor. Clean the
air filter housing.
4. Clean the paper filter by tapping it gently
against a flat surface. If the filter is very dirty,
replace it.
5. Clean the pre-filter. If the filter is very dirty,
replace it.
22
ENGLISH
6. Assemble the filter by performing the above
instructions in reverse order.
9 10 4
Before removing the spark plug, clean around its
mounting.
For the type of spark plug and relative spark gap,
please refer to "0 TECHNICAL DATA TABLE".
9 10 5
See figure (26:A, 27:C,29X:E). The engine is air-
cooled. A blocked cooling system can damage the
engine. Clean the motor air intake. More meticulous
cleaning of the cooling system should be carried
out during each basic service.

9 11 LUBRICATION (28)

Object
Centre
point
Steering
wheel
(740 IOX,
540 IX)
Tensioning
arms
Wheel
bearings
Quick-
release
supports
Control
cables
9 11 1
Destination
Electrical system power supply
Battery charger power supply.
To replace the fuses, proceed as follows:
1. Close the fuel cock (24:B).
2. Open the bonnet (see 7.4).
(Translation of the Original Instructions)

Spark plug

Air intake

Action
3 grease nipples located on
the central articulation on the
left-hand side of the machine.
Use a grease gun filled with
universal grease. Pump until
the grease seeps out.
2 grease nipples located on
the central articulation on the
left-hand side of the machine.
Use a grease gun filled with
universal grease. Pump until
the grease seeps out.
Lubricate the support points
of the tensioning arms with oil.
2 grease nipples.
Use a grease gun filled with
universal grease. Pump until
the grease seeps out.
1 grease nipple for each front
wheel.
Use a grease gun filled with
universal grease. Pump until
the grease seeps out.
Lubricate the control cable
ends with oil.

Fuses (31:F)

Fig
28:A
28:B
28:C
28:D
28:E
28:F
Fuse
20 A
25 A