Bumper Bar; Parking Brake - Chicco TRiOLOVE Gebrauchsanleitung

7. To complete the fitting of the lining on the seat, fasten
the two buttons on the sides (fig. 7), fit the elastic strap
on the relevant hook as shown in fig. 7A and fasten the
buttons in the lower part of the backrest (fig. 7B).
To remove the lining, follow the same steps in the reverse
order.
SAFETY HARNESS
The stroller comes with a five-point safety harness which
consists in two shoulder straps, a lap strap and a crotch
n strap with a buckle.
8. WARNING: when using with children aged 0 to 6
months, you may have to shorten the length of the straps
to adapt them to your baby. To do so, use the shoulder
straps by inserting them first through the adjustment
slots (fig. 8).
9. Make sure the shoulder straps are adjusted at a suitable
height for your child: otherwise, adjust the height (fig. 9).
o 10. After placing your child, put the two forks in the buckle
(Fig. 10) and adjust the width of the waist belt if need-
ed, pressing on the buckles. To unfasten the waist belt,
press the two lateral forks at the same time (fig. 10A).
WARNING: To ensure the safety of your child, you must use
the crotch strap, waist belt and safety harness at the same
time.
WARNING: After removal of the safety harness (e.g. for
washing), ensure that the harness is reassembled correctly
using the anchorage points. The harness must be re ad-
justed.

BUMPER BAR

11. The seat features a bumper bar. To fasten the bar, press
the two buttons located in the lower part of the two
extremities and fit it on the pins located at the end of
the armrests (fig. 11). To remove the bumper bar, follow
the steps described above in the reverse order. You can
e release one side of the bumper bar to let your child to
e seat. The bumper bar can be used both forward facing
and parent facing.
WARNING: Always fasten your child with the safety belts.
h
s The bar IS NOT a device for containing your child.
WARNING: The bar must not be used to lift the product
e
with the child inside of it.
FITTING THE SEAT ON THE STROLLER
12. To attach the stroller seat, insert it in the relevant verti-
cal fastening devices until you hear the click which con-
e firms that it has been fastened (fig. 12). To facilitate fas-
tening the seat on the stroller, please read the instruc-
tions on the lables on both sides of the fabric showing
you the correct alignment of the seat with the fasteners
d (fig. 12 A). The seat can be attached both forward facing
e (fig. 12B) and parent facing (fig. 12C).
WARNING: Before using, make sure that the seat is prop-
d erly locked on by pulling it upwards.
WARNING: If the car seat is not fastened correctly, press
both white buttons on the frame's fasteners and repeat the
fastening procedure making sure that it is locked into place.
Otherwise contact the Chicco technical service.
13. To release the seat, press both buttons under the arm-
rests at the same time (fig. 13) and lift it.
WARNING: The child must never be sitting in the seat
when fastening/unfastening it.
HOOD
14. The seat has two fastening devices located on the sides
of the backrest base which are used to fit the hood. To
fit the hood, slide the clip-on system into the fastening
devices, as shown in fig. 14. Once fastened to the seat,
the hood follows it in forward facing or parent facing
position. To complete fitting the hood on the seat, fas-
ten the rear part of the hood on the back of the stroller
backrest using the relevant buttons (fig 14 A).
15. To open the canopy, push the front arch forward (fig.
15).
16. The hood features a removable net that helps protect
your child from intense light (fig. 16)
17. To remove the rear flap and convert the hood into a
summer sunshade, open the rear zipper (fig. 17) and
unfasten the buttons on the back of the seat's backrest.
18. To remove the hood, simply pull it up and out from the
fastening devices and slide the hooks upwards (fig. 18).
WARNING: The hood must be fixed on both sides of the
stroller. Ensure that the hood is correctly secured into posi-
tion.
HOW TO ADJUST THE BACKREST
19. Press the button on the stroller backrest to recline it to
the desired position (fig. 19). Release the button and the
backrest will click into the closest lock position. Simply
push the backrest up to raise it again.
WARNING: The child's weight can make these operations
more difficult.
HOW TO ADJUST THE LEGREST
20. The legrest has two positions. To adjust it, use the but-
tons under the leg rest (fig. 20).
ADJUSTABLE DOUBLE TWIST ERGONOMIC HANDGRIPS
21. Press the button on the handgrip to rotate it to the re-
quired position, according to the height and position
most suited to the user (fig. 21). The handgrip can be
adjusted to 8 different positions.
22. WARNING: when using the stroller, the handgrips must
not be in the DOWN position (fig. 22). Make sure that the
handgrips are locked in the UP position, as shown in fig.
22 A.
JOINED HANDGRIP
23. To join the handgrips together, match pins A and B with
the relevant holes (fig. 23) until you hear the click.
24. To disengage the joined handgrips, press the two cen-
tral levers inward at the same time (fig. 24) and pull it up
and out (fig. 24 A).
WARNING: before using the product with joined hand-
grips, checks always that they are fastened correctly.
WARNING: Never use the joined handgrips to lift the stroll-
er with your child on board.

PARKING BRAKE

The parking brake acts on both stroller's rear wheels at the
same time The stroller features a STOP AND GO system to
guarantee ease of use; it is marked with coloured stickers
on the rear brake levers.
25. To brake the stroller, press the right lever down (fig. 25).
15