Operation - Powerfix Profi Z31780 Bedienungs- Und Sicherheitshinweise

Fasten the handle on to the mount
3
with the projecting screw thread and the cor-
responding nut (see Fig. A).
Note: Please bear in mind that the angle
grinder must be fitted with a suitable cutting
disc before assembly. It is not possible to
change the disc with the angle grinder in-
stalled in the product.
Now prepare for mounting the angle grinder
in the mount .
24
Note: At this point, first check the size of
the handle thread of your angle grinder. It
may be M6, M8 or M10.
Then place the corresponding mounting
bolts , washers and matching nuts
8 7
distance pieces and plastic bushings
10
to one side, ready for use.
Insert the necessary plastic bushings
the mounting pieces
11
Note: Ensure that the size of the plastic
bushings matches the required mounting
6
bolts . Plastic bushings are not required
8
for mounting bolts M10
Screw the matching mounting bolt
through the rear mounting piece
Fig. B).
Fasten the rear mounting piece
by tightening the corresponding size of nut
on the mounting bolt
9
in the direction of the mounting piece
(see Fig. B).
Insert the adjustment screw
bottom hole and the adjustment screw
through the top hole of the mount
Fig. E). Note that later the rubber buffers of
these screws must lie against the angle
grinder housing.
Note: First insert these screws so that the rub-
ber buffers lie directly against the mount
Now push the plastic locating pieces
the mounting pieces
11
of the mount (see Fig. B).
24
Then attach the mounting pieces
through the plastic locating pieces
the hexagonal socket head screws
elongated holes in the mount
24
,
9
6
into
6
, (see Fig. B).
26
.
8
8
(see
26
in place
26
(i.e. by turning it
8
)
26
through the
13
1
(see
24
.
24
of
12
, on to the guide
26
,
11 26
with
12
in the
19
(see Fig. B).
24
Place the desired distance piece
mounting bolt and washer
8
front mounting piece
11
Note: The three distance pieces
choosing the most appropriate cutting depth.
Note: Set the distance piece
cutting disc cannot come into contact with
the workbench / table below the base plate
(see Figure E).
20
Screw the matching mounting bolt
through the front mounting piece
Fasten the front mounting piece
by tightening the corresponding size of nut
on the mounting bolt
9
in the direction of the mounting piece
Now set the adjustment screws
that the angle grinder is aligned at right
angles to the base plate
attached to the mount
After slightly loosening the hexagonal socket
head screws , adjust the saddle
23
that the cutting disc of the angle grinder
lowers into centre of the slot provided in the
base plate .
20
Now attach the safety guard
push the safety guard
rod and fasten it in place with the wing
2
nut (see Fig. C).
4
Now insert the metal rod
sponding opening in the mount
it in place with the wing screw
Always keep the angle grinder's mains lead
in place using the clip
After assembly is complete, switch the angle
grinder on for a few seconds and then
switch it off again. Check again that all the
screws, bolts and fixings are firmly seated.

Operation

Adjust the guide bolts
piece placement.
Place the workpiece on to the base plate
against the rear stop
18
rotating rotary adjustment knob
on the
10
on to the
7
(see Fig. D).
are for
10
so that the
10
8
.
11
in place
11
(i.e. by turning it
8
).
11
, so
1 13
and firmly
20
(see Fig. E).
24
so
21
. To do this
5
on to the metal
5
into the corre-
2
and fasten
24
(see Fig. C).
27
.
25
for desired work-
16
20
and secure it by
.
14
GB/IE/NI 9