Fitting Procedure - Panasonic TY-WK32LX20W Installationsanleitung

Fitting procedure

1. Confirm the strength of the proposed fitting location
The weight of the wall hanging bracket is approximately 3 kg (6.6
lb.). When fitted to the LCD TV, the total weight is approximately
23 kg (50.7 lb.) (32") or approximately 18 kg (39.7 lb.) (26").
Check the wall strength at the 6 attachment locations by referring
to the dimension drawing of the wall hanging bracket (given at
right), and provide adequate reinforcement if strength is not
sufficient.
Note
There are 12 holes in the wall hanging bracket.
If the wall material is wood, and adequate attachment strength
cannot be ensured by fastening at the 6 points at right, use as
many spare holes as necessary. However, exercise care because
some wall materials may crack if screws are located too close
together. The following dimensions are important. Do not fit at
any location where these dimensions cannot be secured.
Dimensions of clearance required around wall hanging bracket
A
32" 1000 (39 3/8) 558 (21 31/32) 135 (5 5/16)
26" 844 (33 15/64) 478 (18 13/16) 135 (5 5/16)
2. Fit wall hanging bracket to wall
• Fit so that the arrow marks on the wall hanging bracket point upward.
• If the wall consists of a material such as concrete and bolts or nuts must be embedded
beforehand, determine the hole positions by aligning using the actual wall hanging
bracket, or calculate hole positions based on the dimension drawing, and then embed
"M6" bolts or nuts. When embedding bolts, locate so that the bolts protrude from the
wall by 10 to 15 mm (25/64 to 19/32 inches).
(1) Fasten the screw at the top center hole first.
(2) Using a level, correct any bracket inclination, and then fasten screws at the remaining
5 locations.
Note
Use commercially available M6 screws suited to the wall surface material
(wood, steel frame, concrete etc.) for fitting the bracket to the wall.
3. Prepare the LCD TV
∗ Remove the TV stand from the LCD TV.
Carefully store the removed TV stand.
Fit the insulation spacers to
the LCD TV.
Place the LCD TV unit face down on a
blanket or other soft cloth that is clean and
free of debris, and follow the procedure
below.
(1) Remove the terminal cover at the lower
center of the TV's backside.
∗ Refit the removed terminal cover after
wiring.
(2) Affix the included cover stickers (1 each
for left and right) to the stand pole holes
on the bottom of the TV. (Peel off the
backing paper and affix the cover
stickers to cover the holes.)
(3) Fix the included Allen head countersunk
screws, the dished toothed washers and
insulation spacers (4 sets) into the
insulation spacer fastening screw holes
using the included Allen wrench as
shown at right.
4
B C
Unit: mm (inches)
Insulation spacer fastening screw hole
Remove the TV stand.
Remove the screws (4 pcs).
Terminal cover
A
480 (18 57/64)
440 (17 21/64)
176 (6 59/64) 163 (6 27/64)
LCD TV
external
216 (8 1/2)
profile
Wall hanging bracket
Wall attachment holes (at 6 points)
∗ Be sure to fit screws and tighten securely.
∗ Provide spacing for the LCD TV of at least 100
mm (3 15/16 inches) to the top and right side, at
least 300 mm (11 13/16 inches) to the left side,
at least 100 mm (3 15/16 inches) to the bottom
and at least 42 mm (1 21/32 inches) to the rear.
Stand pole hole
Cover sticker
Fit into the
lower hole.
1 Allen head
countersunk screw
2 Dished toothed
washer
3 Insulation spacer
4 Allen wrench