Before Starting The Equipment; General Information - EINHELL TE-SM 2131 Dual Originalbetriebsanleitung

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.

5.1 General information

•
The equipment must be set up where it can
stand securely, i.e. it should be bolted to a
workbench, a universal base frame or similar.
•
All covers and safety devices have to be pro-
perly fitted before the equipment is switched
on.
•
It must be possible for the blade to run freely.
•
When working with wood that has been pro-
cessed before, watch out for foreign bodies
such as nails or screws, etc.
•
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted
and that the equipment's moving parts run
smoothly.
5.2 Assembling the saw (Fig. 1-5)
•
Fasten the transport handle (34) to the machi-
ne head (4) using the supplied screws.
•
Insert the guide pins of the adjustable workpi-
ece supports (10) into the mounting holes on
the machine housing. Tighten the fastening
screws at the guide pins in order to secure
the workpiece supports against falling out.
•
To adjust the turntable (17), loosen the lo-
cking screw (14) by approx. 2 turns and press
the button (42), thus freeing the turntable
(17).
•
Turn the turntable (17) and scale pointer (15)
to the desired angular setting on the dial (16)
and lock into place with the locking screw
(14). The saw has locking positions at angles
of - 45°, -30°, -22.5°, -15°, 0°, 15°, 22.5°, 30°
and 45°.
•
To release the saw from its position at the
bottom, pull the fastening bolt (25) out of the
motor mounting while pressing down lightly
on the machine head (4). Turn the fastening
bolt (25) through 90° before releasing it, so
that the saw remains unlocked.
•
Swing up the machine head (4).
•
The clamping device (8) can be fitted on the
left or right of the fixed saw table (18).
•
The clamping device (8) can be fastened with
the locking screw (26).
Anl_TE_SM_2131_Dual_SPK9.indb 25 Anl_TE_SM_2131_Dual_SPK9.indb 25
GB
•
For the horizontal clamping of workpieces you
can anchor the clamping device in the holder
(44).
•
To move out the workpiece supports (10)
press the lever (d) on the bottom side of the
workpiece support and then pull the workpie-
ce support outwards to the right or left.
•
For repeat cuts of identical length you can
unfold the longitudinal stop (41).
•
When the locking grip (21) is undone, you can
tilt the machine head (4) to the left or right by
up to 45°.
•
To ensure that the saw is standing securely,
adjust the adjustable foot (13) by turning it so
that the saw stands in a horizontal and firm
position.
•
Note: The combination key (45) should be
kept on the back of the machine (see Fig. 1b).
•
The machine can be secured to a workbench,
a universal base frame or similar via the
mounting holes (c).
5.3 Adjusting the miter angle on the machine
head (Fig. 1, 2, 6)
•
Undo the locking grip (21).
•
Hold the machine head (4) by the handle (1)
•
After pulling the button (33), the machine
head can be tipped infinitely as well as to se-
veral locking points.
•
Angles to the left: 0-45°
•
Angles to the right: 0-45°
•
Re-tighten the locking screw (21).
5.4 Precision adjustment of the stop for cros-
scut 90° (Fig. 7-10)
•
Fasten the turntable (17) in 0° position.
•
Undo the locking grip (21) and tilt the machi-
ne head (4) all the way to the right using the
handle (1).
•
Place the 90° angular stop (a) between the
blade (7) and the turntable (17).
•
Open the counternut on the adjustment screw
(39).
•
Adjust the adjustment screw (39) until the
angle between the blade (7) and the turntable
(17) equals 90°.
•
Then tighten the counternut again.
•
Finally check the position of the pointer (20)
on the scale (19). If necessary, undo the poin-
ter (20) with a Philips screwdriver, set it to the
0° position on the scale (19) and retighten the
retainer screw.
•
No stop angle included.
- 25 -
24.10.2019 07:09:27 24.10.2019 07:09:27