Technical Data; Before Starting The Equipment - EINHELL TE-AP 18/26 Li Originalbetriebsanleitung

4. Technical data

Motor power supply: ............................... 18 V DC
Stroke speed: ...................................0-2600 min
Stroke height: ........................................... 26 mm
Cutting depth, wood: .............................. 180 mm
Cutting depth, iron: ................................... 12 mm
Cutting depth for plastic ........................... 20 mm
Maximum saw blade width: ..................... 1.8 mm
Weight: .......................................................2.1 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L sound pressure level ................... 86.08 dB(A)
pA
K uncertainty ............................................. 5 dB
pA
L sound power level ..................... 97.08 dB(A)
WA
K uncertainty ............................................. 5 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Cutting wooden boards
Vibration emission value a
Uncertainty K = 1.5 m/s
Cutting wooden beams
Vibration emission value a
Uncertainty K = 1.5 m/s
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Anl_TP_AP_18_26_Li_SPK13.indb 15 Anl_TP_AP_18_26_Li_SPK13.indb 15
GB
-1
= 15.44 m/s²
h
2
= 18.37 m/s
2
h
2
- 15 -
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Warning!
Always remove the battery pack before making
adjustments to the equipment.
5.1 Changing the saw blade (Fig. 2)
Warning!
Switch off the universal saw and pull out the bat-
tery pack each time before doing any work on the
machine and changing the blade.
To adjust the soleplate, press the soleplate lo-
cking button (5) on the right-hand side (looking
from the top) in order to unlock the soleplate (3).
Set the required distance and press the soleplate
locking button (5) on the left-hand side (looking
from the top) in order to lock the soleplate again.
Check that the soleplate is secure.
5.2 Adjusting the soleplate (Fig. 3)
Warning!
Pull out the battery pack.
14.10.2021 13:53:12 14.10.2021 13:53:12