Crivit HG04400 Montage-, Bedienungs- Und Sicherheitshinweise Seite 6

Trampolines shall neither be installed over concrete, asphalt or any other
hard surface nor at proximity of other conflicting installations (e.g. pad-
dling pools, swings, slides, climbing frames);
Modification of trampoline is not allowed.
The self-locking nuts are for one-time use only and new nuts must
24
be used each time the product is assembled.
Particular caution – Risk of injury for children
Keep the packaging materials away from children. There is a risk of suf-
focation!
Parents and other supervisors should be aware of their responsibility as
situations and conduct may arise for which the exercising equipment was
not designed due to the playfulness and experimentation that is natural
in children.
If you allow your children to use the product you should take their mental
and physical development into account and, most importantly, their tem-
perament. Supervise the children and always instruct them on how to use
the product correctly.
Store the product out of the reach of children when not in use.
Risks from wear
The product may only be used when in perfect condition. Examine the
product for damage and wear before each use. The safety of the product
can only be guaranteed if it is examined regularly for damage and wear.
Discontinue use if damage is found.
Avoiding damage to property
Avoid contact with sharp, hot, pointed, or hazardous objects. Please
ensure that your exercising area is free of pointed objects.
Prior to assembling
To assemble this product all you need is the wrench and special spring
loading tool provided with this product.
During periods of non-use the product can be easily disassembled and
stored.
Please read the assembly instructions before beginning to assemble the
product.
Please refer to page for part descriptions and numbers. The assembly steps
use these descriptions and numbers as reference for your convenience.
Make sure that you have all parts listed. If you are missing any parts,
please contact the producer.
To prevent any injuries to your hands from pinch points during assembly,
please use gloves to protect your hands.
Moving the trampoline
In order to move the trampoline you should have as many helpers as the
trampoline has feet. Prior to lifting, all used fasteners (pegs, etc.) should
be removed. Caution! Due to the spring tension there is a possible risk that
the frame can be twisted as a result of uneven lifting. You and your helpers
should therefore be respectively positioned between two feet of the trampoline
and you should then all lift the trampoline at the same time. Lift the trampoline
off the ground slightly and keep it horizontal with the floor. To move the
trampoline in a different way, disassemble it completely. To disassemble,
follow instructions for assembly backwards.
Assembly
Tools required:
1 x wrench (included)
14
1 x screwdriver (included)
21
1 x tool to tension the spring (included)
28
6 GB
Step 1 (Fig. A-G)
Please select all angled rods
and common sections
12a 12b
tions. All parts with the sample part number are interchangeable, and to
connect the parts, simply slide section tubing that is smaller on one end
into adjacent section that has a larger opening.
Note: Frame rods` punching holes upwards. While inserting the
5
extension rod into the common section
8a
the both parts align.
The bottom screw hole of extension rod
rod facing inward of the trampoline and then thread a self-tapping
4
screw by screwdriver .
16 21
The common section and extension rod are in alternately with hole
and without hole on an angled rod
8a 12b 8b
Step 2 (Fig. H-L)
When attaching springs to the mat
11
to help you with this portion of the assembly.
CAUTION! When attaching the springs
pinch points since the product is tightening up.
Lay out the jump mat with the printed side facing upwards in the product.
1
Position the circular hook of spring
use the tool to tension the springs
to the hole on the frame rods
Note: Refer to Fig. H for which hook of spring
frame rod .
5
Select an arbitrary point on the frame rods
Thereby, attach the first spring
Count 15 holes from point ZERO in one direction. Thereby attach the
second spring . Attach two further springs
11
that now four springs are respectively attached in quarter-circle intervals.
11
Securely attach a further spring
notice that you have skipped a hole and an eyelet, recount and remove
or attach any springs required to maintain the rest of springs.
11
Step 3 (Fig. M-N)
Place the frame protection
2
and the frame are covered.
Please ensure that the frame protection covers all metal parts.
Place the elastic drawstrings so that every other string led over a common
section.
Fasten the drawstrings at the back of the common section. Knot the two
ends together.
Step 4 (Fig. O-Q)
Connect the lower enclosure pole
Put the pole cap on the upper enclosure pole
15
screw , as Fig. O.
16
Mount the enclosure poles support with poles onto the trampoline leg
using the spacer , screws
23 13
the nuts using provided wrench
Note: Use nut on the upper hole of trampoline leg (hole of common
24
section ), and use cap nut
12a
pole ).
8a
Note: Nut is one time use only. The nylon lock in the nut may dam-
25
age after use, and so it must be replaced for a re-assembly.
Step 5 (Fig. R-U)
Spread out Enclosure net
3
with the doorway and align the net as to where you would like to get in
and out of the product. Fasten the buckle of the enclosure net
pole cap .
15
Knot the rope on an eyelet of the jump mat
27
shown alternately through the eyelet of the jump mat
sure net . Ensure the enclosure net
3
eyelets of the jump met .
1
IMPORTANT: All snap closures must be once again clamped securely
so that the enclosure net becomes taut. If the enclosure net is not taut, it
cannot complete this function as designed.
, frame rods , extension rods
4 5
according to the products from the illustra-
, ensure the screw holes of
12a
and screw hole of angled
8a
.
4
, please invite another person
1
, the tube joints can become
11
on the eyelet of the jump mat
11
to link up the round hook of spring
28
.
5
to the mat
11
(designate it as point ZERO).
5
.
11
at the same interval, so
11
in the middle of each quarter. If you
11
on the assembled frame, so that the springs
and upper enclosure pole
6
and secure with
7
, nut , cap nut and washer
24 25
. Repeat until all the poles are set up.
14
on the lower hole (hole of extension
25
on the trampoline mat. Locate the panel
. Then thread is as
1
and the enclo-
1
is completely well tired on all
3
8a 8b
12a
,
1
11
and
1
.
7
. Firm
26
on the
3