Lock Function; Magnetic Sensor; Minute Minder (Countdown) - Scholtes SH09DLTAB Gebrauchsanweisung

zone will show a luminous signal alternating between "0"
GB
and "H". If the hob is switched to the OFF setting (A),
the luminous signal will display the letter "H" in a fixed
manner.
Warning:
To prevent damage being inflicted on the electronic cir-
cuits, the hob is fitted with an overheating safety system.
In situations where the appliance is used at high power
levels for a prolonged period of time, the hob may switchoff
one or more of the activated zones temporarily, until the
temperatures return to the set levels.
On the display corresponding to the cooking zone which
has been temporarily switched off, the power level will be
shown in alternation with a E/2.
This will stop flashing once the cooking zone has been-
reactivated.
Lock function (fig.2 - (B))
To prevent the hob from being used by children, all
functions may be locked by pressing the Lock button
(B); this function is active when the indicator light (C) is
illuminated.
- To activate or deactivate it, press and hold button (B)
for approximately two seconds.
- If the hob is switched on and the Lock function is
enabled, button A will still work.
Magnetic sensor (fig.2 - (I))
- The hob is equipped with a pan sensor; when the pan is
removed or badly positioned, the
If, on the other hand, the surface of the glass is still hot,
the symbol will appear alternating with the .
O.S.D. (Overflow Safety Device) (fig. 2)
The hob is equipped with a safety system which moves
all hotplates to the OFF position and activates the safety
lock when liquids or items are detected on the control
panel A.
These symbols will flash on the display:
. They can be deactivated by removing the item
or the liquid. The hob will switch off automatically.
Attention!
When the hob switches on, the timer display Q stays on
at the value If the function is not activated, after a few
seconds the display Q shows nothing.
Timer (fig.2 - (Q)):
Note: The Timer can be activated on all 4 cooking zones
at the same time.
This function allows to establish the time (from 1 to 99
minutes) or automatic switch-off of the cooking zone
selected.
18
Activation:
1- Select the cooking zone (E).
2- Set the cooking level (from 1 to 9) desired, by acting
on the SLIDER control (D1).
3- Press the Timer button (N), the display will show
At this point, the hob indicator (O) with the timer function
active, starts to flash.
4- Set the unit time (N2) desired from 0 to 9 by acting on
the SLIDER control (D1) e.g.
5- After a few seconds the unit value (N2) and the tenths
(N1) will appear fixed on the display
6- At the end of the programmed time, the timer display
(Q) and the hob indicator (O) will start to flash followed
by an acoustic sound.
To deactivate the acoustic signal just press the timer
button N, otherwise it will deactivate automatically after
2 minutes.
To deactivate the timer function before the set time:
- select the cooking zone (E) and press one of the two
buttons (N).
When the zone indicator (R) on display (E) stops flashing,
the function is no longer active.
Note: To display the residual cooking time, just press the
cooking zone (E) of interest selection button.
symbol will appear;
Minute Minder (Countdown) (fig.2 - (Q))
- The Minute Minder allows to set an established count-
down that goes from 1 to 99 minutes.
On expiry of the time, the hob emits an acoustic signal
without changing the active functions.
- The function activates only if the cooking level is set at
"0" on all displays (R).
- Press the Timer button (N) and set the time with the same
procedure as the Timer function, with the unique exception
that the indicators (O) do not switch on.
Note: Whenever the Timer is to be activated on at least
one zone, the Minute Minder deactivates automatically.
To activate the Timer instead of the Minute Minder,
proceed as follows:
1- Use one of the buttons to select (E) the cooking zone
where the timer function is to be activated.
2- Set the cooking level by acting on the SLIDER control
(D1).
3- Select the Timer button (N).
4- Select the button (E) again where the timer function is
to be activated.
5- Select the Timer button (N).
- if you want to set a time exceeding 9 minutes e.g:
, just run your finger over the SLIDER control (D1).
- if, on the contrary, no operation is performed, it stops
flashing after a few seconds and the Timer display (Q)
will show the cooking time previously set
Attention! This function can only be used if no
cooking zone (E) has the timer inserted.
,
.
;
.